All Projects

opengles and op_power.sh don't like each other very much.
whenever returning from low power to full power mode again, opengles rendering is just dead.

the reason for this issue are following 2 lines within op_power.sh

18 echo 0 > /sys/devices/platform/omapfb/graphics/fb0/blank
...
66 echo 1 > /sys/devices/platform/omapfb/graphics/fb0/blank

if these lines are removed/commented, the gles rendering just resumes fine.

Found I'd kept some notes about making the Pandora's wake on alarm function work...

drivers/rtc/rtc-twl4030.c

twl4030_rtc_remove (for when the driver is removed) and twl4030_rtc_
shutdown (for when the system is shutdown) functions need to change. Or at least the shut down does.

oh YUK who's been using goto....

changes in drivers/rtc/rtc-twl4030.c

twl4030_rtc_remove
commented out //mask_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_ALARM_M);

twl4030_rtc_shutdown
replaced
// mask_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_TIMER_M |
// BIT_RTC_INTERRUPTS_REG_IT_ALARM_M);
with
mask_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_TIMER_M);

twl4030_rtc_suspend
replaced
// mask_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_TIMER_M |
// BIT_RTC_INTERRUPTS_REG_IT_ALARM_M);
with
mask_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_TIMER_M);

twl4030_rtc_init
added (before return!)
twl4030_rtc_alarm_irq_set_state(true);

Should probably check reg 0x2B with mask 0x08 to see if alarm should be left enabled or not ?
but only in twl4030_rtc_shutdown and ?remove? NOT in twl4030_rtc_init
should remove ever happen ???

I'm guessing it's best to not enable the alarm irq's all the time???

PyGame is damn slow (games with scrolling are not at all playable).
Would be nice if Hardware surface could be used :)

When a X window which is displaying GLES2 render output is:
- Either dragged out of the visibile screen region (?)
- Is made larger than it was at the creation time of the GLES2 context
then:
- The performance will drop significantly as the EGL buffer swaps won't occur as fast as before,
- The render output will be corrupted and flicker
- In rare occasions crashes the application or locks up the entire system (which forces you to remove the battery)

The problem can not be solved without restarting the application (Possibly forcing players to complete the same goals again as they were unable to reach a savepoint or similar things).

This was confirmed in Mupen64Plus and the PowerVR GLES Samples and some of my own projects (which are, however, based on the PowerVR samples).
As I didn't see any other reports about this problems (but had it confirmed by other Pandora users too) I would expect that it can be fixed by using a newer X, kernel or combination of them as other OMAP users would be effected too.

On OS Zaxon (hotfix 3).

With "xfconf-query", the resolution is 800x480@60 Hz.
But with the tool in the menu "Settings" -> "Display", the resolution is 800x480@0 Hz.

With Java (opensdk-6-jre 6b18-1.8),

GraphicsEnvironment.getLocalGraphicsEnvironment().getDefaultScreenDevice().getDisplayModes()

return 1 display mode that is 800x480@0 Hz with a BPP of -1.

It seems to be the reason that GraphicsEnvironment.getLocalGraphicsEnvironment().getDefaultScreenDevice().getDisplayMode() return null
and when closing a java application that goes in fullscreen mode to throw an exception (invalid display mode).

With both Hotfix 3 and Hotfix 4 Beta the Run PND Application menu item fails to do anything.

Possibly related problem is that PND files newly copied to SD card are not recognized and entered on desktop as expected.
When you go to Thunar and right click - execute the PND file, nothing happens.
Possible fix by copying the PND to another folder on the SD card with Thunar.
This makes at least two PND files I had work.

Still no response with "Run PND Application" menu, though.

Try clearing shortcuts in Start->Settings->Window Manager->Keyboard. That doesn't work (for me).
This is a problem because these shortcuts are blocking key-combination in apps, like for example the keymapper in dosbox (CTRL+F1) or refreshing content (CTRL+F5). I tried manual editing or even deleting the configuration file, but changes are not recognized and the file recreated on reboot.

Ok, I just want to say that there is something missing about the font on the base image. I cant get what (at least for now)

Here is an issue : http://www.gp32x.com/board/index.php?/topic/54282-getting-vnc-viewer-to-work/

With my current Ogre build I get :
Warning: Unable to load any usable ISO8859 font
Error: Aborting: no font found

I've googled but so far no solution :(

using evdev xorg drivers and not the tslib drivers you can receive pressure axis data however there is
a problem with the values reported by the ads7846 module and the evdev driver has no calibration property for pressure

using
xinput test touchscreen
you can see the pressure axis ranging from 120-ish for hard press to about 150-170 for light press (low pressure values can
be quite erratic)

I could possibly hack the evdev module to possibly do something with this odd and narrow range of values, but I rather think looking
at the source that the ads7846 module needs some work.

is there a git tag that has a known working configuration? as I've had problems getting the kernel to compile the last few times I attempted...

FLAWED BEHAVIOUR:

Copy and paste only works between 2 active applications. This is very limiting!
If you are in the single task oriented MiniMenu you have no chance at all to share the clipboard between apps!
If you are in the multi tasking oriented XFCE desktop environment you can only share between apps running in parallel! Not with apps which started after the source app has been terminated.

DESIRED BEHAVIOUR:

The clipboard content (within reasonable limits of course) should remain, regardless of the source application, so that you can paste at any later moment into any application.

This seems to be the case with Hot-fix 5 and 6 alpha 4.

I've been able to repeat this bug by re-flashing..

On a fresh re-flash.. installed community codec pack.. Videos will play fine on Panplayer, VLC and Gnome-Mplayer with default settings, which I believe is XV or SDL out in the case of VLC.

Run the TV-out script it will cause a blank black screen during playback.. Disabling TV-out, switching modes, rebooting.. battery out, nothing seems to allows it to work with XV/SDL out again.. I know If I switch to X11 it will make it "work" again, but I notice a bit of lag during playback using X11 compared to XV/SDL out.

This is the related documentation:
http://pandorawiki.org/Power_modes#Low_Power
(Please update accordingly as part of the issue resolution)

FROM MY USER EXPERIENCE:

If you put the Pandora into Low Power Mode, then press some keys, and then wake the Pandora back into Normal Mode, your input (both keys and nubs, haven't tried with USB input yet) seem to have triggered something while the device was in Low Power Mode!

What does really happen in Low Power Mode concerning execution and input?

a) Input is received AND triggers as application execution continues
or
b) Kernel/driver queues the input signals into a buffer, and executes them on wake?

If supposition a) or b) is true, then this would be one more reason to properly implement:  FS#259 

OBSERVANCE EXAMPLE 1:

1) Start MiniMenu. Mentally note down your active tab.
2) Put Pandora to Low Power Mode.
3) Press shoulder button R once.
4) Wake Pandora to Normal Mode. You are now one tab to the right of where you left. Input must have been caught in Low Power Mode, but wether execution of it happened while Low Power Mode or later after wake in Normal power Mode is unclear.

OBSERVANCE EXAMPLE 2:

1) Start gedit (a text editor). Insert the digit "1".
2) Put Pandora to Low Power Mode.
3) Press: CTRL-N 2 CTRL-N 3 CTRL-N 4. (Without the spaces)
4) Wake Pandora to Normal Mode.
5) For a fraction of a second you see the tabs building up. Either the input was really received AND executed while Low Power Mode and what you see is just a delayed window manager refreshment, or the input was queued in Low Power Mode, and only executed on wake.

Steps to reproduce the bug(s):

1) In MiniMenu select an arbitrary app.
2) Press SPACE to bring up the contextual menu.
3) Select "Edit notes line 1".
4) Insert your string and confirm.
5) Now at a later time you may decide to remove your note line again. Therefore you select the same app again in MiniMenu, then repeat steps 2-3, but this time:

a) Erase all characters so that you get an empty string and then confirm. RESULT: Your change is simply ignored! There should be a possibility within MiniMenu to remove/reset note lines, the simplest being to simply accept an empty string as an input, that's what an average user will try if s/he does not find a dedicated "Delete note line" command.

b) As a workaround I tried something and detected yet another bug! As I could not create an empty string, I simply created a note line only containing 1 SPACE character (=the string " ") and confirmed. This got accepted.

If MiniMenu is in detailed view mode (press the A-button or TAB in order to bring it up, if it is not already there) and you slide over an app whose note line is " ", MiniMenu crashes!

Maybe the bug is connected with the writing to / the parsing from the .OVR (override) files which MiniMenu creates for the affected files, as the separating value in OVR files seems to be TAB, and SPACE is also WHITESPACE, therefore some parsers probably skip/misinterpret this, and MiniMenu then catches an unexpected situation!

WORKAROUND: If you ran into the problem, that you cannot get rid of the note lines anymore, simply start a file browser of your choice, navigate to the location of the affected .PND file and find its sister .OVR (override) file and delete it or edit it accordingly!

I assigned personal subcategories to some of my games.
Some of those subcategories share the same beginning string, i.e: Shooter, ShooterBallistic ShooterScoller.
MiniMenu displays those subcategories with flaws! See the ASCII screenshots below.
Note: The star symbols indicate the currently active selection.

The main category tab "Game" being active:

----------------------------------------------------------
| All | Audio | AudioVideo | Education |*Game*| Graphics |
----------------------------------------------------------
ActionGame AdventureGame ArcadeGame BlocksGame ...
Shooter ShooterBallistic ShooterScroller ...
GameA GameB GameC ...
----------------------------------------------------------

Now if I navigate into the sub-category "Shooter", everything normal:

----------------------------------------------------------
|*Shooter*|
----------------------------------------------------------
.. ShooterA ShooterB ShooterC ...
----------------------------------------------------------

But if I navigate to the sub-category "ShooterBallistic", strangely MiniMenu shows 2 tabs, "Shooter" and "ShooterBallistic", and jumps right into "Shooter".

----------------------------------------------------------
|*Shooter*| ShooterBallistic |
----------------------------------------------------------
.. ShooterA ShooterB ShooterC ...
----------------------------------------------------------

In order to reach my intended tab "ShooterBallistic" I need to navigate to it again. Annoying. There the contents are as expected:

----------------------------------------------------------
| Shooter |*ShooterBallistic*|
----------------------------------------------------------
.. ShooterBallisticA ShooterBallisticB ShooterBallisticC
----------------------------------------------------------

The flaw is the same for all other sub-categories beginning with "Shooter...". All have the flaw as shown in the example "ShooterBallistic", only that it is themselves instead of "ShooterBallistic". One more example to be perfectly clear:

----------------------------------------------------------
| Shooter |*ShooterScroller*|
----------------------------------------------------------
.. ShooterScrollerA ShooterScrollerB ShooterScrollerC
----------------------------------------------------------

The update mode functions have moved from the DSS layer to omapfb implementaion.
This patch exports the new function symbols for use by the TI drivers.

--- a/drivers/video/omap2/omapfb/omapfb-ioctl.c
+++ b/drivers/video/omap2/omapfb/omapfb-ioctl.c
@@ -22,6 +22,7 @@

#include <linux/fb.h>
#include <linux/device.h>
+#include <linux/module.h>
#include <linux/uaccess.h>
#include <linux/platform_device.h>
#include <linux/mm.h>
@@ -359,6 +360,7 @@ int omapfb_set_update_mode(struct fb_info *fbi,

return r;
}
+EXPORT_SYMBOL(omapfb_set_update_mode);

int omapfb_get_update_mode(struct fb_info *fbi,
enum omapfb_update_mode *mode)
@@ -381,6 +383,7 @@ int omapfb_get_update_mode(struct fb_info *fbi,

return 0;
}
+EXPORT_SYMBOL(omapfb_get_update_mode);

/* XXX this color key handling is a hack... */
static struct omapfb_color_key omapfb_color_keys[2];

The last release of TI Graphics SDK Product to support the 1.0.3 SGX core is 4.04.00.03
The overlay needs to peg the package selection to this version.

This patch when applied aginst TI 4.04.00.03 SGX drivers will allow building the pvr kernel modules.
This relies on task 272 (kernel patch) and should be used inconjuction with task 273

diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/3rdparty/dc_omapfb3_linux/omaplfb_displayclass.c b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/3rdparty/dc_omapfb3_linux/omaplfb_displayclass.c
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/3rdparty/dc_omapfb3_linux/omaplfb_displayclass.c 2011-06-20 21:03:33.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/3rdparty/dc_omapfb3_linux/omaplfb_displayclass.c 2012-02-09 08:37:21.000000000 +1100
@@ -830,7 +830,11 @@
unsigned long ulLCM;
unsigned uiFBDevID = psDevInfo->uiFBDevID;

+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,38)
+ console_lock();
+#else
acquire_console_sem();
+#endif

psLINFBInfo = registered_fb[uiFBDevID];
if (psLINFBInfo == NULL)
@@ -972,7 +976,11 @@
ErrorModPut:
module_put(psLINFBOwner);
ErrorRelSem:
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,38)
+ console_unlock();
+#else
release_console_sem();
+#endif

return eError;
}
@@ -982,7 +990,11 @@
struct fb_info *psLINFBInfo = psDevInfo->psLINFBInfo;
struct module *psLINFBOwner;

+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,38)
+ console_lock();
+#else
acquire_console_sem();
+#endif

psLINFBOwner = psLINFBInfo->fbops->owner;

@@ -993,7 +1005,11 @@

module_put(psLINFBOwner);

+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,38)
+ console_unlock();
+#else
release_console_sem();
+#endif
}

static OMAPLFB_DEVINFO *OMAPLFBInitDev(unsigned uiFBDevID)
diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/3rdparty/dc_omapfb3_linux/omaplfb_linux.c b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/3rdparty/dc_omapfb3_linux/omaplfb_linux.c
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/3rdparty/dc_omapfb3_linux/omaplfb_linux.c 2011-06-20 21:03:33.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/3rdparty/dc_omapfb3_linux/omaplfb_linux.c 2012-02-09 13:14:28.000000000 +1100
@@ -24,11 +24,14 @@
*
******************************************************************************/

+
+#include <linux/version.h>
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,38)
#ifndef AUTOCONF_INCLUDED
#include <linux/config.h>
#endif
+#endif

-#include <linux/version.h>

#include <asm/atomic.h>

@@ -236,8 +239,11 @@
struct fb_var_screeninfo sFBVar;
int res;
unsigned long ulYResVirtual;
-
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,38)
+ console_lock();
+#else
acquire_console_sem();
+#endif

sFBVar = psDevInfo->psLINFBInfo->var;

@@ -268,31 +274,37 @@
printk(KERN_INFO DRIVER_PREFIX ": %s: Device %u: fb_pan_display failed (Y Offset: %lu, Error: %d)\n", __FUNCTION__, psDevInfo->uiFBDevID, psBuffer->ulYOffset, res);
}
}
-
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,38)
+ console_unlock();
+#else
release_console_sem();
+#endif
}

OMAPLFB_UPDATE_MODE OMAPLFBGetUpdateMode(OMAPLFB_DEVINFO *psDevInfo)
{
struct omap_dss_device *psDSSDev = fb2display(psDevInfo->psLINFBInfo);
OMAP_DSS_DRIVER(psDSSDrv, psDSSDev);
-
- enum omap_dss_update_mode eMode;
-
- if (psDSSDrv == NULL || psDSSDrv->get_update_mode == NULL)
- {
- DEBUG_PRINTK((KERN_INFO DRIVER_PREFIX ": %s: Device %u: Can't get update mode\n", __FUNCTION__, psDevInfo->uiFBDevID));
- return OMAPLFB_UPDATE_MODE_UNDEFINED;
+ if (psDSSDrv == NULL || psDSSDev == NULL)
+ {
+ DEBUG_PRINTK((KERN_INFO DRIVER_PREFIX ": %s: Device %u: No DSS device\n", __FUNCTION__, psDevInfo->uiFBDevID));
+ }
+ enum omapfb_update_mode eMode;
+
+ if (!omapfb_get_update_mode(psDevInfo->psLINFBInfo, &eMode))
+ {
+// DEBUG_PRINTK((KERN_INFO DRIVER_PREFIX ": %s: Device %u: Can't get update mode\n", __FUNCTION__, psDevInfo->uiFBDevID));
+ return OMAPLFB_UPDATE_MODE_AUTO;
+// return OMAPLFB_UPDATE_MODE_UNDEFINED;
}

- eMode = psDSSDrv->get_update_mode(psDSSDev);
switch(eMode)
{
- case OMAP_DSS_UPDATE_AUTO:
+ case OMAPFB_AUTO_UPDATE:
return OMAPLFB_UPDATE_MODE_AUTO;
- case OMAP_DSS_UPDATE_MANUAL:
+ case OMAPFB_MANUAL_UPDATE:
return OMAPLFB_UPDATE_MODE_MANUAL;
- case OMAP_DSS_UPDATE_DISABLED:
+ case OMAPFB_UPDATE_DISABLED:
return OMAPLFB_UPDATE_MODE_DISABLED;
default:
DEBUG_PRINTK((KERN_INFO DRIVER_PREFIX ": %s: Device %u: Unknown update mode (%d)\n", __FUNCTION__, psDevInfo->uiFBDevID, eMode));
@@ -307,10 +319,10 @@
{
struct omap_dss_device *psDSSDev = fb2display(psDevInfo->psLINFBInfo);
OMAP_DSS_DRIVER(psDSSDrv, psDSSDev);
- enum omap_dss_update_mode eDSSMode;
+ enum omapfb_update_mode eDSSMode;
int res;

- if (psDSSDrv == NULL || psDSSDrv->set_update_mode == NULL)
+ if (psDSSDrv == NULL)
{
DEBUG_PRINTK((KERN_INFO DRIVER_PREFIX ": %s: Device %u: Can't set update mode\n", __FUNCTION__, psDevInfo->uiFBDevID));
return OMAPLFB_FALSE;
@@ -319,20 +331,20 @@
switch(eMode)
{
case OMAPLFB_UPDATE_MODE_AUTO:
- eDSSMode = OMAP_DSS_UPDATE_AUTO;
+ eDSSMode = OMAPFB_AUTO_UPDATE;
break;
case OMAPLFB_UPDATE_MODE_MANUAL:
- eDSSMode = OMAP_DSS_UPDATE_MANUAL;
+ eDSSMode = OMAPFB_MANUAL_UPDATE;
break;
case OMAPLFB_UPDATE_MODE_DISABLED:
- eDSSMode = OMAP_DSS_UPDATE_DISABLED;
+ eDSSMode = OMAPFB_UPDATE_DISABLED;
break;
default:
DEBUG_PRINTK((KERN_INFO DRIVER_PREFIX ": %s: Device %u: Unknown update mode (%d)\n", __FUNCTION__, psDevInfo->uiFBDevID, eMode));
return OMAPLFB_FALSE;
}

- res = psDSSDrv->set_update_mode(psDSSDev, eDSSMode);
+ res = omapfb_set_update_mode(psDevInfo->psLINFBInfo, eDSSMode);
if (res != 0)
{
DEBUG_PRINTK((KERN_INFO DRIVER_PREFIX ": %s: Device %u: set_update_mode failed (%d)\n", __FUNCTION__, psDevInfo->uiFBDevID, res));
@@ -441,10 +453,17 @@
OMAPLFB_ERROR OMAPLFBUnblankDisplay(OMAPLFB_DEVINFO *psDevInfo)
{
int res;
-
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,38)
+ console_lock();
+#else
acquire_console_sem();
+#endif
res = fb_blank(psDevInfo->psLINFBInfo, 0);
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,38)
+ console_unlock();
+#else
release_console_sem();
+#endif
if (res != 0 && res != -EINVAL)
{
printk(KERN_WARNING DRIVER_PREFIX
@@ -459,9 +478,17 @@

static void OMAPLFBBlankDisplay(OMAPLFB_DEVINFO *psDevInfo)
{
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,38)
+ console_lock();
+#else
acquire_console_sem();
+#endif
fb_blank(psDevInfo->psLINFBInfo, 1);
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,38)
+ console_unlock();
+#else
release_console_sem();
+#endif
}

static void OMAPLFBEarlySuspendHandler(struct early_suspend *h)
@@ -692,9 +719,17 @@
flush_workqueue(psDevInfo->psSwapChain->psWorkQueue);
}

+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,38)
+ console_lock();
+#else
acquire_console_sem();
+#endif
ret = fb_blank(psDevInfo->psLINFBInfo, iFBMode);
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,38)
+ console_unlock();
+#else
release_console_sem();
+#endif

OMAPLFBCreateSwapChainUnLock(psDevInfo);

@@ -717,7 +752,6 @@
static int __init OMAPLFB_Init(void)
#endif
{
-
if(OMAPLFBInit() != OMAPLFB_OK)
{
printk(KERN_WARNING DRIVER_PREFIX ": %s: OMAPLFBInit failed\n", __FUNCTION__);
diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/common/resman.c b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/common/resman.c
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/common/resman.c 2011-06-20 21:03:34.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/common/resman.c 2012-02-09 23:33:43.000000000 +1100
@@ -24,15 +24,17 @@
*
******************************************************************************/

+#include <linux/version.h>
#include "services_headers.h"
#include "resman.h"

#ifdef __linux__
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,38)
#ifndef AUTOCONF_INCLUDED
#include <linux/config.h>
#endif
+#endif

-#include <linux/version.h>
#include <linux/sched.h>
#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,9)
#include <linux/hardirq.h>
diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/event.c b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/event.c
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/event.c 2011-06-20 21:03:34.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/event.c 2012-02-09 09:00:12.000000000 +1100
@@ -24,11 +24,14 @@
*
******************************************************************************/

+#include <linux/version.h>
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,38)
#ifndef AUTOCONF_INCLUDED
#include <linux/config.h>
#endif
+#endif

-#include <linux/version.h>
#include <asm/io.h>
#include <asm/page.h>
#if (LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,22))
diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mmap.c b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mmap.c
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mmap.c 2011-06-20 21:03:34.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mmap.c 2012-02-09 08:56:41.000000000 +1100
@@ -24,11 +24,14 @@
*
******************************************************************************/

+#include <linux/version.h>
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,38)
#ifndef AUTOCONF_INCLUDED
#include <linux/config.h>
#endif
+#endif

-#include <linux/version.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <linux/vmalloc.h>
diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mm.c b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mm.c
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mm.c 2011-06-20 21:03:34.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mm.c 2012-02-09 08:52:48.000000000 +1100
@@ -24,11 +24,14 @@
*
******************************************************************************/

+#include <linux/version.h>
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,38)
#ifndef AUTOCONF_INCLUDED
#include <linux/config.h>
#endif
+#endif

-#include <linux/version.h>
#include <linux/mm.h>
#include <linux/vmalloc.h>
#include <asm/io.h>
diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mm.h b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mm.h
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mm.h 2011-06-20 21:03:34.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mm.h 2012-02-09 08:55:49.000000000 +1100
@@ -27,11 +27,14 @@
#ifndef __IMG_LINUX_MM_H__
#define __IMG_LINUX_MM_H__

+#include <linux/version.h>
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,38)
#ifndef AUTOCONF_INCLUDED
#include <linux/config.h>
#endif
+#endif

-#include <linux/version.h>
#include <linux/slab.h>
#include <linux/mm.h>
#include <linux/list.h>
diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/module.c b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/module.c
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/module.c 2011-06-20 21:03:34.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/module.c 2012-02-09 08:59:05.000000000 +1100
@@ -24,9 +24,13 @@
*
******************************************************************************/

+#include <linux/version.h>
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,38)
#ifndef AUTOCONF_INCLUDED
#include <linux/config.h>
#endif
+#endif

#if !defined(SUPPORT_DRI_DRM)

@@ -44,7 +48,6 @@
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/module.h>
-#include <linux/version.h>
#include <linux/fs.h>
#include <linux/proc_fs.h>

diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mutils.c b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mutils.c
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mutils.c 2011-06-20 21:03:34.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mutils.c 2012-02-10 00:24:09.000000000 +1100
@@ -24,10 +24,13 @@
*
******************************************************************************/

+#include <linux/version.h>
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,38)
#ifndef AUTOCONF_INCLUDED
#include <linux/config.h>
#endif
-#include <linux/version.h>
+#endif

#include <linux/spinlock.h>
#include <linux/mm.h>
diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mutils.h b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mutils.h
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mutils.h 2011-06-20 21:03:34.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mutils.h 2012-02-09 08:54:31.000000000 +1100
@@ -27,11 +27,13 @@
#ifndef __IMG_LINUX_MUTILS_H__
#define __IMG_LINUX_MUTILS_H__

+#include <linux/version.h>
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,38)
#ifndef AUTOCONF_INCLUDED
#include <linux/config.h>
#endif
-
-#include <linux/version.h>
+#endif

#if !(defined(__i386__) && (LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,26)))
#if defined(SUPPORT_LINUX_X86_PAT)
diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/osfunc.c b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/osfunc.c
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/osfunc.c 2011-06-20 21:03:34.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/osfunc.c 2012-02-09 09:01:16.000000000 +1100
@@ -24,11 +24,14 @@
*
******************************************************************************/

+#include <linux/version.h>
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,38)
#ifndef AUTOCONF_INCLUDED
#include <linux/config.h>
#endif
+#endif

-#include <linux/version.h>
#include <asm/io.h>
#include <asm/page.h>
#if (LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,22))
diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/proc.c b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/proc.c
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/proc.c 2011-06-20 21:03:34.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/proc.c 2012-02-09 08:57:49.000000000 +1100
@@ -24,13 +24,16 @@
*
******************************************************************************/

+#include <linux/version.h>
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,38)
#ifndef AUTOCONF_INCLUDED
#include <linux/config.h>
#endif
+#endif

#include <linux/init.h>
#include <linux/module.h>
-#include <linux/version.h>
#include <linux/fs.h>
#include <linux/proc_fs.h>
#include <linux/seq_file.h>
diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/pvr_debug.c b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/pvr_debug.c
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/pvr_debug.c 2011-06-20 21:03:34.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/pvr_debug.c 2012-02-09 23:54:38.000000000 +1100
@@ -24,9 +24,12 @@
*
******************************************************************************/

+#include <linux/version.h>
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,38)
#ifndef AUTOCONF_INCLUDED
#include <linux/config.h>
#endif
+#endif

#include <asm/io.h>
#include <asm/uaccess.h>
@@ -72,7 +75,7 @@
static PVRSRV_LINUX_MUTEX gsDebugMutexNonIRQ;

-static spinlock_t gsDebugLockIRQ = SPIN_LOCK_UNLOCKED;
+static DEFINE_SPINLOCK(gsDebugLockIRQ);

#if !defined (USE_SPIN_LOCK)
#define USE_SPIN_LOCK (in_interrupt() || !preemptible())
diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/pvr_drm.c b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/pvr_drm.c
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/pvr_drm.c 2011-06-20 21:03:34.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/pvr_drm.c 2012-02-16 01:58:14.000000000 +1100
@@ -26,14 +26,16 @@

#if defined(SUPPORT_DRI_DRM)

+#include <linux/version.h>
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,38)
#ifndef AUTOCONF_INCLUDED
#include <linux/config.h>
#endif
+#endif

#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/module.h>
-#include <linux/version.h>
#include <linux/fs.h>
#include <linux/proc_fs.h>
#include <linux/sched.h>
@@ -371,11 +373,23 @@
.poll = drm_poll,
.fasync = drm_fasync,
},
+#if (LINUX_VERSION_CODE <= KERNEL_VERSION(2,6,38))
.pci_driver =
{
.name = PVR_DRM_NAME,
.id_table = asPciIdList,
},
+#else
+ .kdriver =
+ {
+ PVR_DRM_NAME,
+ asPciIdList,
+ },
+// {
+// .pci->name = PVR_DRM_NAME,
+// .pci->id_table = asPciIdList,
+// },
+#endif

.name = PVR_DRM_NAME,
.desc = PVR_DRM_DESC,
@@ -385,6 +399,13 @@
.patchlevel = PVRVERSION_BUILD,
};

+#if (LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,39))
+static struct pci_driver pci_pvr_driver = {
+ .name = PVR_DRM_NAME,
+ .id_table = asPciIdList,
+};
+#endif
+
static int __init PVRSRVDrmInit(void)
{
int iRes;
@@ -401,7 +422,11 @@
}
#endif

+#if (LINUX_VERSION_CODE <= KERNEL_VERSION(2,6,38))
iRes = drm_init(&sPVRDrmDriver);
+#else
+ iRes = drm_pci_init(&sPVRDrmDriver,&pci_pvr_driver);
+#endif
#if defined(PVR_DRI_DRM_NOT_PCI)
if (iRes != 0)
{
@@ -413,7 +438,11 @@

static void __exit PVRSRVDrmExit(void)
{
+#if (LINUX_VERSION_CODE <= KERNEL_VERSION(2,6,38))
drm_exit(&sPVRDrmDriver);
+#else
+ drm_pci_exit(&sPVRDrmDriver,&pci_pvr_driver);
+#endif

#if defined(PVR_DRI_DRM_NOT_PCI)
drm_pvr_dev_remove();
diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/pvr_uaccess.h b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/pvr_uaccess.h
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/pvr_uaccess.h 2011-06-20 21:03:34.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/pvr_uaccess.h 2012-02-09 08:51:21.000000000 +1100
@@ -27,11 +27,14 @@
#ifndef __PVR_UACCESS_H__
#define __PVR_UACCESS_H__

+#include <linux/version.h>
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,38)
#ifndef AUTOCONF_INCLUDED
#include <linux/config.h>
#endif
+#endif

-#include <linux/version.h>
#include <asm/uaccess.h>

static inline unsigned long pvr_copy_to_user(void __user *pvTo, const void *pvFrom, unsigned long ulBytes)

In GTK applications, such as Truecrypt, NoteCase Pro or Mousepad, the file open / file save dialogs have shortcuts to mounted file systems on the left side.
If clicking such a shortcut entry, the corresponding file system's contents are shown in the right dialog pane.
This works for file systems, which were available at boot time.
For file systems mounted after booting, e.g. by inserting an SD card or connecting a USB drive, when clicking such an entry, an error message appears saying
"Could not mount [volumen name]
Failed to execute child process 'gnome-mount' (No such file or directory)"

This is healed by
sudo opkg install gnome-mount
(which instals gnome-mount, nautilus, gvfsd-ftp, gvfs (upgrade), and a lot of libs (upgrades)..

This has been seen in SuperZaxxon release 1.5, not in Beta3 (but Beta3 is the only choice in Flyspray's dropdown currently).

I reported that error for HF6 I think, and it seemed to be fixed in SuperZaxxon Beta5. A regression?

If a PND has been run as root before (using pnd_run.sh from a root shell) and afterwards it is invoked the normal way, the PND doesn't start, because the .out file cannt be overwritten:

/usr/pandora/scripts/pnd_run.sh: line 26: /tmp/pndrun_firefox.out: Permission denied

Desired solution:
.out file is silently overwitten.
Maybe, if that's not possible, create another .out file with a different name (added counter, for example).

Seen in SuperZaxxon relese 1.5, not in Beta3 as this task is flagged, but there is no choice besides Beta3.

As verified with xev, an attached bluetooth keyboard can not generate colon (shift semicolon). xmodmap shows that (unlike a standard Linux system) shift-semicolon is mapped to NoSymbol. While it's find that there's a special symbol to get semicolon on the built-in keyboard, the other binding really should be there in support of attached keyboards.

Hi, sadly the XFCE bluetooth manager seems to have problems with pairing simple SPP devices (an BT GPS mouse here).

1. Enable BT
2. BT Manager -> Add new device
3. Confirm Dialog and wait for scanning
4. Pick device
5. Select PIN options -> "0000" (here for me)
In next step the dialog still asks you to enter a random PIN at your BT device (which is impossible here).

Thus it seems, that the XFCE dialog makes troubles, I tried it with 2 different GPS. Pairing the GPS manually works fine:
sudo rfcomm connect rfcomm0 00:18:E4:26:5F:14

When put into Hold mode, X11 handles the power switch as if it's being pressed, and it generates lots of keypress events, passing them to the foreground application. Since /dev/input/eventX does not seem to continuously trigger, I'm guessing it's due to key repeat.

To reproduce:

• Install xev and open it in the terminal


• Put the power key in HOLD mode


• Notice the "time" value changing rapidly

In addition to causing more work to X, it also floods the active application with key presses, resulting in increased CPU usage. In my test, switching to HOLD while Firefox is in the foreground causes it to use 6% CPU and X an additional 2.5%.

In addition, the key-press events continue even after the switch is taken off HOLD until another key is pressed.

A possible solution to this is to blacklist the power-button event device, to prevent evdev from listening to it (the key is handled by pndevmapperd).

The touch screen requires to be used with the stylus or another sharp object. Even if I need to click a desktop icon, and could as well use my finger, the touch screen won't react to my finger at all (even if pressed quite hard).

If you boot the system with the lid closed, the backlight will still be on when you get to the desktop. You have to lift the lid for an instant and then close again to shut it off. Perhaps this is because of the lack of trigger for an interrupt since the sensor is already activated. Can there be one extra check of the lid sensor after boot to cover this static position?

FAAD2 appears to not be compiled with fixed point decoding. My version of libfaad compiled with fixed point used 2-3x less cpu than the provided one. It's not enough to provide the switch to the configure script. the file libfaad/common.h has to be edited and a define uncommented. Line 68 in the v2.7 source.

/* COMPILE TIME DEFINITIONS */

/* use double precision */
/* #define USE_DOUBLE_PRECISION */
/* use fixed point reals */
//#define FIXED_POINT <<<<<------------