|
151 | Base OS | Feature Request | Medium | [PATCH] Turn Off LCD when closing the lid | Closed | |
Task Description
Just added a few lines to op_lid.sh, will power off the LCD when you close the LID. Patch attached. |
|
153 | Application | Feature Request | Low | [PATCH] HACK: change OPP level according to set Mhz | Closed | |
Task Description
It's a hack, use on your own risk as always. I feel like abusing the tracker dropping all my patches here, but whatever. Patch attached. |
|
161 | Base OS | Feature Request | Low | Add ftp to base OS | Closed | |
Task Description
Include the netkit-ftp package so the Pandora has at least basic ftp functionality out of the box. |
|
171 | Core | Feature Request | Medium | Update clock from hardware when restoring from low powe ... | Closed | |
Task Description
The clock occasionally does weird things during low power mode, sometimes gaining time, sometimes losing. This is most likely a result of the CPU being reduced to 14Mhz and the system clock being unable to keep up.
A convenient work around is to make a call to "/sbin/hwclock --hctosys" during wake-up to load the hardware clock back into the system clock. This may add an extra second or two to the wake-up time but will prevent confusion caused by clock being very incorrect. |
|
174 | Base OS | Feature Request | Low | Include modem-manager in base image | Closed | |
Task Description
Please consider including the modemmanager package in the base distibution.
This allows 3G wireless dongles to work out of the box (configured via network-manager). |
|
184 | Core | Feature Request | Medium | libpnd: Add a function to get all mounted PNDs | Closed | |
Task Description
Add a function to get all mounted PNDs. Because it's very annoying to check all the menu/desktop folders on all of the SD-Cards. |
|
195 | Core | Feature Request | High | Start re-recharge of battery sooner | Closed | |
Task Description
Increase battery LVL_4 and LVL_3 threshold.
After reaching 100%, in some cases the charge circuit enters "battery full" state, stops charging, and begins to discharge. This is not entirely unexpected behavior according to the spec sheet, although I don't fully understand exactly the situations in which it completes charging. Once the battery is full, the battery will begin discharging. The charge circuit automatically restarts the recharge once the voltage has gone below a certain level (crosses below the LVL_3 voltage threshold)
The default LVL_3 voltage threshold is 3.902 volts which is at about 80-85% battery level as recorded by bq27500 chip. In my opinion, this is way too low.
Setting the BCIMFTH2 register to 0xCB increases the voltage threshold to about 4.003 volts which is about 93%.
Setting it to 0xDC may also be worthwhile, which is just over 95%.
By default, if a user leaves their Pandora plugged in overnight, they may wake up to find their Pandora has stopped charging and the capacity has dropped to almost 80%, which can be quite startling to some users who will then report it as a bug.
This change will ensure that it never drops below 93-95%, a much more acceptable level.
Specific code changes suggested, in the /drivers/power/twl4030_bci_battery.c file, somewhere in the twl4030_bci_battery_probe function (or a function called by it), add the lines:
/********************************/
#define KEY_FTH2 0x7F
#define REG_BCIMFTH2 0x017
ret = twl4030_i2c_write_u8(TWL4030_MODULE_MAIN_CHARGE, KEY_FTH2, REG_BCIMFKEY);
if (ret)
return ret;
ret = twl4030_i2c_write_u8(TWL4030_MODULE_MAIN_CHARGE, 0xDC, REG_BCIMFTH2);
if (ret)
return ret;
/********************************/
(Move defines to the top, as appropriate) |
|
196 | Core | Feature Request | Medium | [PATCH] Add tablet support into kernel | Closed | |
Task Description
Hi,
This should be a quite simple thing, but my first time touching
the OE repo and i cant test it, so be careful. |
|
212 | Core | Feature Request | Low | Add curl to core installed programs | Closed | |
Task Description
I wish for curl to be installed by default on the upcoming pandora FWs,
As reported by the angstrom repo, where I install using the command:
$sudo su
...
#opkg update
#opkg install curl
curl 7.21.2-r4.0.9 is 78.57 Kilobytes with the dependencies
Depends:libcurl4, libgnutls26, libgcrypt11, libgpg-error0, libc6, libz1
I do not know which is installed by default, but I'm sure libc6 is, so I'm going to state the info on the rest of the packages for its memory space usage on the NAND
libcurl4(142.99 Kilobytes):
Command line tool and library for client-side URL transfers.
Depends:libc6, libgnutls26, libz1, libgcrypt11, libgpg-error0, as you can see, it has the same dependencies as above, so it seems both curl and libcurl are probably exclusive from the others, but I will go forward and state the rest of the dependencies
libgnutls26 2.8.6-r10.0.5 (291.44 Kilobytes)
Depends:libz1, libgcrypt11, libgpg-error0, libc6, (again, it looks like the above depends on this)
libgcrypt11 1.4.1-r0.9 (220.35 Kilobytes)
Depends: libgpg-error0, libc6, (Oh look, we're not looking at libz1 anymore)
libgpg-error0 1.4-r7.1.9 (5.78 Kilobytes)
Depends:libc6
now to the lone libz1
libz1 1.2.3-r7.0.9 (41.95 Kilobytes)
Depends:libc6
So, in the case we already have the gpg stuff, then the installation is only 221.56KB, however, with the zlib and the gpg included, the total comes to 781.08KB
So, now that the cost is out of the way, What are the goods and bads?
Good:
Its a very versatile CLI program to get and send information over http through the network, and is tolerant of network issues
It doesn't take too much space relative to things that have been pulled out, like abiword.
The libcurl is a very good library, and could be of great benefit to some future projects.
Bad:
Well, we already have wget, which is not as configurable, and wget hates Craig's appstore
Here's the link to curl on the repo
http://www.angstrom-distribution.org/repo/?pkgname=curl |
|
220 | Core | Feature Request | Low | Please include /usr/bin/xkbset | Closed | |
Task Description
One of the first things after installing HF5 was downloading xkbset, because it is necessary for proper L-R buttons mapping as mouse buttons. Could you please include that in the system?
I am using urjaman's executable from here:
http://www.gp32x.com/board/index.php?/topic/55124-remapping-the-mouse-buttons-etc/page__st__15__p__896576&#entry896576
Even better would be a GUI that allows mapping of L-R buttons for mouse, just like GUI for nubs :) But including xkbset will be already good. |
|
226 | Core | Feature Request | High | Boot from /dev/sda devices requested | Closed | |
Task Description
Boot from usb hard disk not supported. This should be a rather simple fix of adding the sdx devices and adjust the boot scripts??
I was able to put this autoboot.txt on mmc 0:1
setenv bootargs debug root=/dev/sda1 rw rootdelay=2 console=ttyS0,115200n8 vram=6272K omapfb.vram=0:3000K
ext2load sda 0:1 0x80300000 /boot/uImage
bootm 0x80300000
This failed with amongst other things "Block device sda 0 not supported" and something about failing to load kernel
So I then changed the autoboot file to this
setenv bootargs debug root=/dev/sda1 rw rootdelay=2 console=ttyS0,115200n8 vram=6272K omapfb.vram=0:3000K
ext2load mmc 0:3 0x80300000 /boot/uImage
bootm 0x80300000
All this did was die after the kernel loaded.
I believe I could much better make use of this device if I could boot from some faster storage, please advise :) |
|
234 | Core | Feature Request | Medium | Changeable behaviour when closing the lid | Closed | |
Task Description
As it was requested on forum.gp2x.de and I think it's a good idea I've written some scripts to allow the user to change what happens when the lid is opened/closed.
There are 3 Settings:
-The old behaviour (turning off the screen)
-Go into low power mode
-Shutdown
Default behaviour is still the same: Turn the screen off. Maybe we could change this to low power mode? I don't know.
I made a lot of changes to op_lid.sh: http://pastebin.com/GT3qxWSx (diff: http://pastebin.com/Z8GwpDj8 )
I changed line 11 in op_power.sh to: if [ $powerstate -ne 0 ]; then
And wrote a gui for changing the setting using zenity: http://pastebin.com/9JvSTqfQ
(I still can't upload any files, don't know if it's the fault of my browser, that's why I use this paste service) |
|
241 | Application | Feature Request | Low | MiniMenu shall remember state for next start | Closed | |
Task Description
With the setting "Live (not exit) on app run?" set to "NO" the currently selected tab and item shall be remembered, so that you return to the same state, in which you left MiniMenu. |
|
248 | Core | Feature Request | Medium | Support for hibernation by caching to SD card | Closed | |
Task Description
It would be very desirable that the PandoraOS could hibernate, and that this action can easily be accessed/triggered with either a hotkey or as an action for the max-idle-time-event or lid-close-event.
That would be the battery friendly universal action to quickly pause/resume any arbitrary application/task.
The current standby mode is far to power consuming for breaks longer than ~ 1 hour. Improving standby mode to be more battery-friendly would of course be too highly appreciated and practical.
If hibernation is triggered, RAM content gets written to a special file or partition on a SD card. The boot-manager of course needs to recognize such a RAM-file on SD-cards. In case it finds more than 1, i.e.: multiple cards/partitions, the one with the newest timestamp gets priority.
256MB RAM with about 10-20 MB/s read/write time to SD, would result in 25-12 seconds for going into or out of hibernation, which would be acceptable for me. In practice it would mean, that if I quickly have to pause me OpenPandora operation (i.e. train stop), I just close my lid, and put the Pandora into my pocket (2-4 seconds), and I am then trusting that the rest reliable happens in my pocket (10-20 seconds). |
|
275 | Core | Feature Request | Low | User should be a member of the cdrom group | Closed | |
Task Description
These permissions are needed for CD/DVD burning/player apps.
From bdc88595d8af726b3bf4745ece310f92299d8759 Mon Sep 17 00:00:00 2001
From: Paul Dersey
Date: Sun, 19 Feb 2012 17:22:41 -0500
Subject: [PATCH] pandora-first-run-wizard: add user to cdrom group
---
recipes/pandora-system/pandora-first-run-wizard.bb | 2 +-
.../pandora-first-run-wizard/first-run-wizard.sh | 2 +-
2 files changed, 2 insertions(+), 2 deletions(-)
diff --git a/recipes/pandora-system/pandora-first-run-wizard.bb b/recipes/pandora-system/pandora-first-run-wizard.bb
index 904dc4a..a63dc0c 100755
--- a/recipes/pandora-system/pandora-first-run-wizard.bb
+++ b/recipes/pandora-system/pandora-first-run-wizard.bb
@@ -6,7 +6,7 @@ RDEPENDS = "hsetroot zenity dbus pandora-wallpaper-official tslib tslib-calibrat
COMPATIBLE_MACHINE = "omap3-pandora"
-PR = "r28"
+PR = "r29"
SRC_URI = " \
file://first-run-wizard.sh \
diff --git a/recipes/pandora-system/pandora-first-run-wizard/first-run-wizard.sh b/recipes/pandora-system/pandora-first-run-wizard/first-run-wizard.sh
index a801e3f..f30b80e 100755
--- a/recipes/pandora-system/pandora-first-run-wizard/first-run-wizard.sh
+++ b/recipes/pandora-system/pandora-first-run-wizard/first-run-wizard.sh
@@ -88,7 +88,7 @@ while ! username=$(zenity --title="Enter your username" --entry --text "Please c
zenity --title="Error" --error --text="Please try again." --timeout 6
done
-while ! useradd -c "$name,,," -G adm,audio,video,netdev,wheel,plugdev,users "$username" ; do
+while ! useradd -c "$name,,," -G adm,audio,cdrom,netdev,plugdev,users,video,wheel "$username" ; do
username=$(zenity --title="Please check username" --entry --text "Please ensure that your username consists of only\nletters and numbers and is not already in use on the system." --entry-text "$username")
done
--
1.7.8.3 |
|
276 | Core | Feature Request | Low | Kernel 3.2.x: add script to activate zram | Closed | |
Task Description
Please add a script to activate zram (RAM compression) when using the new kernel. More info about how to do this is available in this post:
http://boards.openpandora.org/index.php?/topic/7844-superzaxxon-beta-3-released/#entry138834
http://boards.openpandora.org/index.php?/topic/7226-superzaxxon-beta-11-released/page__st__20#entry128665
Please be aware though that Linux-SWAT had to explicitly set a value in "/sys/block/zram0/disksize" to get it work with Slackware. Over here the following is automatically set:
pandora:~$ cat /sys/block/zram0/disksize
61648896
Sadly I can *not* change this value, even using sudo:
pandora:~$ ls -l /sys/block/zram0/disksize
-rw-r--r-- 1 root root 4096 Apr 9 12:51 /sys/block/zram0/disksize
pandora:~$ cat /sys/block/zram0/disksize
61648896
pandora:~$ sudo echo 61648888 > /sys/block/zram0/disksize
-bash: /sys/block/zram0/disksize: Permission denied
Basically the following commands are required in a startup script to automatically create the "compressed swap inside RAM" aka zram (possibly a check if the modprobe was successful makes sense as well as checking for the size of the created ramdisk):
modprobe zram
mkswap /dev/zram0
swapon -p 5 /dev/zram0 |
|
279 | Core | Feature Request | Medium | pidgin requires (more) locales to work correctly | Closed | |
Task Description
Please add the following package to allow umlauts working in pidgin:
glibc-gconv-utf-16
After installing this package I no longer have a problem receiving umlauts in pidgin. Besides it might also make sense to add "glibc-gconv-cp1250" which might be required for western europe and koi8-r which seems to be missing for xchat and conversion of chars there.
At the moment the following locale related packages are installed (as of SuperZaxxon Beta3):
glibc-charmap-utf-8 - 2.9-r35.3.5
glibc-gconv - 2.9-r35.3.5
glibc-gconv-cp1252 - 2.9-r35.3.5
glibc-gconv-ibm850 - 2.9-r35.3.5
glibc-gconv-iso8859-1 - 2.9-r35.3.5
glibc-gconv-iso8859-15 - 2.9-r35.3.5
Please add:
glibc-gconv-cp1250
glibc-gconv-koi8-r
glibc-gconv-unicode
glibc-gconv-utf-16
Thanks! |
|
321 | Core | Feature Request | Low | Support overriding all category fields with .ovr | Closed | |
Task Description
Currently only the main category and the first sub category of the main category can be overridden using a .ovr file while libpnd uses additional PXML supplied category date to construct the desktop file. This makes it difficult to work with PNDs that supply unwanted data in these additional fields. |
|
250 | Application | Feature Request | Medium | File Browser Thunar - Trashing file crosses filesystem ... | Researching | |
Task Description
Trashing a file/folder seems to MOVE it to a certain trash directory on the MAIN VOLUME, rather then the ORIGINATING VOLUME, hence this can result in a COPY RATHER THAN A MOVE operation, if the trashed file originates from a filesystem other than the main filesystem!
This is very inefficient and faulty as it is:
a) Very time consuming
b) And in case of large files this operation can even fail due to not enough free space on the main volume. |
|
65 | Core | Feature Request | Very Low | .desktop files, be nice if they included the non-englis... | New | |
Task Description
.desktop files only include the English stuff right now (using the .desktop default tags.)
Be nice if in addition to 'title', we also include 'title[de]' type extras, whatever is in the PXML.xml
pnd_pxml_t includes all the goods, but pnd_disco_t has only the summarized english stuff. |
|
105 | Application | Feature Request | Very Low | Nubs feature request | New | |
Task Description
The 'Nubs' application needs a setting for deadzone. Using the nubs in First person shooters the nubs trigger in directions when not even touched. An adjustment for deadzone would eliminate accidental movement caused by vibration.
Also, application profiles for the nubs would be very useful. Different apps use the nubs in different ways and it would be great to not have to go and change settings before launching each application. |
|
106 | Application | Feature Request | Very Low | AppData corruption | Unconfirmed | |
Task Description
The appdata folder was corrupted on my SD card from an unclean eject this made the folder read only until i ran a repaired it. MiniMenu still displayed all my PND files.
When clicking to launch the app would try to load crash and then return to MiniMenu without any visible error. This was pretty confusing and i thought it might be a good fix for a troubleshooting guide. |
|
108 | Base OS | Feature Request | Critical | TUN/TAN-Driver | Closed | |
Task Description
There is no TUN/TAN Driver installed. This is recommanded for some encrypted wireless lan connections, especially for eduroam, a world wide access point for the education community. Also, a tun-driver is also recommended for vpnc. |
|
118 | Base OS | Feature Request | Low | add sdl-perl to the base OS | Unconfirmed | |
Task Description
Hi there,
Many games depend on sdl-perl. Perl and sdl are part of the base OS, but not not the connection between the two.
Cheers,
sebt3 |
|
123 | Base OS | Feature Request | Low | Suggestions for the Pandora-Button | New | |
Task Description
My suggestion instead of a full menu, would be to have a tiny overlay over the current running application which allows you to:
- relogin (to close all running applications)
- quit (stop the active application)
- shows the last notifications / toaster messages which you missed while being in a fullscreen app.
- possibly even something like plugin support or icons to check out the wifi-strength etc. from fullscreen apps.
Implementation wise this could possibly be done using
- a topmost window and the same content rendered in screenspace in a GLES hook (which should draw over most applications)
or
- one of the DSS2 overlays maybe
It's definitely something to consider as it was requested on the forums a few times (~"xbox like menu in games"). |
|
156 | Base OS | Feature Request | Very Low | Ask to format SD Card | Unconfirmed | |
Task Description
When I have received my Pandora, I got an SD Card but it was not formated. I didn't have any card reader so I didn't now what was wrong (the Pandora or the SD Card).
When an unformated SD Card is inserted in the Pandora, it should be nice to ask if we want to format it. |
|
209 | Core | Feature Request | Medium | Shutdown after a full charge | Unconfirmed | |
Task Description
That still need to be configurable, but chris_c does a good job I'ld like to see integraded in the main image :
http://www.gp32x.com/board/index.php?/topic/58794-a-script-to-shutdown-after-charging/
and :
http://chrisc.bedroomcoders.co.uk/?p=77 |
|
210 | Core | Feature Request | Medium | Wader - cross platform graphical assistant for 3g conne... | Unconfirmed | |
Task Description
http://www.wader-project.org
http://trac.wader-project.org
http://trac.wader-project.org/wiki/Developers
this would be really usefull to monitor reception/network of mobile broadband dongle and it also counts ur mobile data usage (for those that have limits). |
|
217 | Application | Feature Request | Low | Add Mounting and unmounting context options for PND's | Unconfirmed | |
Task Description
It'll have to be in the SKEL.
/etc/skel/Applications/Settings/Thunar/uca.xml
People can replace the contents of their current uca.xml file with the following to gain this functionality now.
/home/[USERNAME]/Applications/Settings/Thunar/uca.xml
Terminal
Open Terminal Here
exo-open --working-directory %f --launch TerminalEmulator
Example for a custom action
*
emblem-symbolic-link
Mount PND
/usr/pandora/scripts/pnd_run.sh -p %f -m && thunar /mnt/utmp/
*.pnd;*.PND
gtk-jump-to-rtl
Unmount PND
/usr/pandora/scripts/pnd_run.sh -p %f -u
*.pnd;*.PND |
|
238 | Application | Feature Request | Low | Quick key access to OK in dialogues | Unconfirmed | |
Task Description
PROBLEM DESCRIPTION: In many GUI dialogues the default action button (OK, ACCEPT, YES, …) cannot be triggered with a simple key press. Pressing ENTER triggers the element which has focus (usually the first dialogue element), but not the default action, as most computer users would expect!
MY WORKAROUND MEANWHILE: Press ALT plus the underlined letter of your desired action. But that's not very convenient as the underlined letter needs to be looked upon first, as the button label can differ from situation to situation (ACCEPT, OK, YES, …) and then 2 keys need to be pressed.
SUGGESTED SOLUTION: The custom of many operating systems should be adapted on the OpenPandora as well. SPACE triggers the currently focused element (whatever that may be: list item, radio button, checkbox, etc), and ENTER triggers the default action of that dialogue.
Or even better use the Pandora specific A/B/Y/X keys cleverly in those dialogues/selections. I don't know whether there is a standard functionality assignment within this key-group, in MiniMenu "B" is start/confirm, I do not know of any other standard assignments yet. |
|
239 | Application | Feature Request | Low | MiniMenu: New option: Grid stop horizontal | Unconfirmed | |
Task Description
I am suggesting the new option "Grid stop horizontal" for MiniMenu with the following possible settings and their effect.
Yes -> If the boundary is reached the focus remains there.
No -> If the boundary is reached the focus starts at the opposite side again.
Jump to next/prev line -> If the boundary is reached the focus jumps to the next/previous line and the opposite side. |
|
240 | Application | Feature Request | Low | MiniMenu shall return into full screen mode (more quick... | Unconfirmed | |
Task Description
If you set MiniMenu's option "Live (not exit) on app run?" to YES, and you quit an application and return to the still running MiniMenu, it runs in windowed mode, and takes about 2 seconds until it goes into full screen mode again.
This delay should at best be not noticeable at all, at most 0-1 seconds. |
|
242 | Application | Feature Request | Medium | Pressing SHIFT + any key in sequence creates the modifi... | Unconfirmed | |
Task Description
ISSUE ENVIRONMENT:
If you hold your Pandora in your hands, you only have your thumbs for typing, hence your typing abilities are quite limited.
It is hard to press more than 2 keys, and hard to press 2 keys on the same side, as your second thumb does not reach the opposite side all too easy (except you have a basketball player's hands).
The modifier keys Start/ALT Select/CTRL Pandora/(META, I guess?) are in the middle of the keyboard, hence the can easily pressed together with another key. But SHIFT lies at an ergonomically problematic side (left boundary). Hence hard to press with other left side keys.
SUGGESTED SOLUTION:
I suggest that Pandora OS offers an optional and configurable input help.
[1|2|3 presses | hold for duration x] SHIFT [timeout y] [modifier key 2] [timeout z] key
Produces the same result like SHIFT + modkey2 + key
Very likely modifier key 2 and timeout z are not necessary, as you can trigger the SHIFT hold (by your defined action), and then press the modifier key 2 and the other key at once, as the other modifier keys are laid at a central (ergonomically better) position. |
|
243 | Application | Feature Request | Medium | MiniMenu: Pressing successive character keys should com... | Unconfirmed | |
Task Description
Imagine this tab content:
Nubs, Pandora Input, PNDstore.
CURRENT BEHAVIOR:
Pressing "P" and "N" is succession jumps to "Nubs" eventually, as it first jumps to the first "P" item ("Pandora Input"), then to the first "N" item, "Nubs".
DESIRED BEHAVIOR:
That it acts like in most Linux file browsers or the Mac OS X Finder.
In detail: Pressing "P" and "N" within a certain time limit should combine them to the string "PN" and jump to the first item which starts with that string, i.e. "PNDStore". If no item matches, reduce the combination string by one character, try to match again, if that doesn't match, try matching again with one character less, ... , until only one character is left, and if that one doesn't match jump to the nearest previous lexicographical character, which matches. |
|
244 | Application | Feature Request | Low | Include man and the manpages | Unconfirmed | |
Task Description
The command line environment of the default OS does not include the command "man" and the respective manpages of the installed programs.
I personally often use manpages, as I hardly remember the syntax/arguments of all programs I use.
Having them would be very convenient!
EVALUATING NEEDED STORAGE AMOUNT
Some may argue that storage space is quite limited on the NAND.
Yes I agree. Hence the number of included programs is limited too. Hence it would not be all too many manpages.
When I press TAB into an empty Terminal prompt, I get 1406 possibilities, which is about the amount of available commands/programs if we ignore aliases, etc.
Multiply that with an average of 20 kb per manpage, and you get about 30 MB in total. With compression this could possibly be brought down to 15-20 MB.
POSSIBLE SOLUTIONS
A) Store into the NAND the manpages of core OS CLI programs only, and not all the library/system/etc documentation.
B) Include only the man command into the core OS, and compile/configure it in such a fashion, that it finds the manpages within non-NAND media (SD card, USB volume, etc).
b1) Specify that it simply looks into a certain path within the /media/*/pandora/ structure.
b2) Or offer PND packages like man-core.pnd, man-extended.pnd,... you get the idea or even man-custom.pnd (which would look into its appdata or a certain path for custom added manpages, to somehow get the b1 approach within the PND approach). |
|
245 | Core | Feature Request | Low | BugTracker: Submitter shall be able to edit bug after p ... | Closed | |
Task Description
I accidentally posted a "feature request" as a "bug report" within the FlySpray BugTracker.
I wanted to correct my mistake.
It was not possible to edit it.
I assigned the bug to myself.
Then I could edit it.
But now I cannot un-assign it from me.
I merely wanted to suggest a feature but not take development responsibility (yet).
For original submitters, who later realize a mistake in their post, there should be a possibility to correct their mistake.
Please un-assign me from #237 #241 #243 and this one #245. Thanks. |
|
251 | Core | Feature Request | Low | SD Mass Storage: Possibility to host multiple volumes | Unconfirmed | |
Task Description
a) Host multiple volumes at once.
b) Select one for hosting first, later host additional ones. (I guess this scenario is more complicated) |
|
252 | Core | Feature Request | Low | Power management: If power cable is plugged ignore "Shu... | New | |
Task Description
If the power cable is plugged and the user chooses "Shutdown Pandora" from a menu, there should be a warning that this is without purpose, as the device will automatically restart.
The resulting user choices should be "Cancel shutdown" and "Shutdown nevertheless". |
|
253 | Application | Feature Request | Medium | Switch GUI: Intelligent automatic choice | Unconfirmed | |
Task Description
If only 2 GUIs are available, skip the user selection and switch right into the only other GUI. What else would the user want?! Right!
If more than 2, already set the focus in the GUI list to the next possible item. |
|
288 | Core | Feature Request | Low | add functionality to inputrc | Unconfirmed | |
Task Description
Since the default inputrc doesn't contain any functionality (simple cli movements like ctrl-left or crtrl-right to skip words don't work) this diff may be useful to add to the cli-experience. I've also been trying to get the delete-key to work, but this is apparently already a known issue (see FS#227). I can remove this from the diff if you want. (I couldn't attach a file to the task somehow)
31,32c31,33
< # "\e[3~": delete-char
< # "\e[2~": quoted-insert
---
> #"\e[3~": delete-char
> "\e[^?": delete-char
> "\e[2~": quoted-insert
44,47c45,50
< # "\e[5C": forward-word
< # "\e[5D": backward-word
< # "\e\e[C": forward-word
< # "\e\e[D": backward-word
---
> "\e[1;5C": forward-word
> "\e[1;5D": backward-word
> "\e[5C": forward-word
> "\e[5D": backward-word
> "\e\e[C": forward-word
> "\e\e[D": backward-word |
|
307 | Core | Feature Request | Medium | Change how Automatic Shutdown works | Unconfirmed | |
Task Description
When thee Pandora is shutting down because its almost out of power, it should check to make sure that the nub inputs are set to the default mode (which is mouse movement for the left nub and mouse buttons for the right nub). If not, it should change them to be like that. |
|
327 | Core | Feature Request | Low | Context menu for the XFCE menu | Unconfirmed | |
Task Description
Right now. the XFCE menu handles right clicks like left clicks. It would be more logical to either not do anything on a right click, or open a context menu that e.g. lets the user generate a link to an application on the desktop. |
|
13 | Core | To Do (Reminder) | Low | verify pndevmapperd is invoking scripts | Closed | |
Task Description
menu button is verified
verify power button
verify lid open/close |
|
14 | Core | To Do (Reminder) | Low | Add hup of pndnotifyd to .xinitrc | Closed | |
Task Description
Pretty minor risk, but if the guy creates multiple accounts on the machine, and logs out of one and into another .. we'll want to hup pndnotifyd
Alternative solution is to poll utmp (or inotify on utmp?) to watch for logins and handle it magicly. |
|
29 | Core | To Do (Reminder) | Low | ToDo: Map Fn-U and Fn-I with brightness controls | Closed | |
Task Description
Include brightness change hotkeys. |
|
34 | Core | To Do (Reminder) | Low | Add software mixer to ALSA | Closed | |
Task Description
Some headphones are very loud. The volume wheel cannot be used properly with them.
Therefore, we should be able to change the volume in software mode, too.
File attached below, simply needs to be included in the next image by DJWillis. |
|
47 | Core | To Do (Reminder) | Medium | evmapperd: Blinking LED and charging control | Closed | |
Task Description
evmapperd should start blinking when the power is getting low.
Ideally, the blinking speed should increase with decreasing battery power and should start maybe at 5% as default (would be nice to have the settings configurable by the user).
As soon as the AC adaptor is connected, blinking should stop.
When the battery power is at 0% it should immediately shutdown and poweroff (NOT to be overridden by the user!)
Aditionally, we should have some charging control (or would it be better using a different daemon for that?)
Here's part of my conversation with MichaelW:
when the charge current was below a threshold, it would reduce the charger input current allowed and take it down to about what the system needs
it would be an active thing constantly sampling the system and constantly updating the input current to match the system
the alternative is that when the battery is full, the charge path is cut off until the battery drops down a bit, maybe 90% |
|
48 | Core | To Do (Reminder) | Low | Create the TV Out Enable / Disable scripts | Closed | |
Task Description
The commands do exist, I just need to wrap them round some zenity scripts. |
|
49 | Core | To Do (Reminder) | Low | Change some of our scripts into internal PNDs | Closed | |
Task Description
Some of our scripts (CPU Speed, Switch Default GUI, Enable TV Out) should be changed into PND format so that pmenu can also run them. |
|
50 | Core | To Do (Reminder) | Medium | pmenu: Add shutdown / logout | Closed | |
Task Description
There's no way yet to shutdown (poweroff) or logout from pmenu yet. |
