|
266 | Application | Bug Report | Low | hf6rc: Unable to enter Low Power Mode with lid shut: | Closed | |
Task Description
Since hf6rc was installed I am unable to enter low power mode.
I did pull up the new lid config settings script and selected switch off screen.
Reproducable.
Nothing happens when the power switch is moved fully to the right for a short time.
I expect it to entry low power mode. quirky for it not too.
workaround: easy - enter LPM before closing lid.
btw: unable to select hf6 in reported version. |
|
264 | Core | Bug Report | Low | Issues with HOTFIX 6 R1 Beta | Closed | |
Task Description
I started with hotfix 5 and when I used the Left Nub for mouse movement it performed well.
I installed HOTFIX 6 R1 Beta and the Nub works fine except pushing up. It moves the cursor very slow and all other directions just fine. The other nub works just fine as well.
This only began after I installed HF6R1B.
I also had to install the Hotfix twice due to sustained system freeze upon start up on the first attempt.
I enabled gui choice but minimenu does not function it just cycles back to GUI choice. |
|
263 | Application | Bug Report | Critical | MiniMenu with "Auto discover pnd apps?" set to NO hangs ... | Closed | |
Task Description
BUG DESCRIPTION:
On my SD card with Pandora OS 1.6.4 I changed MiniMenu's setting "Auto discover pnd apps?" to NO, and then the program remained in an endless loop showing "Setting up menu...", crashing, "Setting up menu...", crashing, and so on.
BUG REPRODUCTION:
The variable filesystem.do_pnd_disco set to the value 0 definetely causes the crash, but maybe only in conjunction with some of my other settings?!
Therefore see my attached config file mmpref.conf.
Maybe related to FS#79 , hard to tell, as this is a very minimal report.
Definitely not related to my previously reported MiniMenu bug FS#262
WORKAROUND:
1) If your default GUI is:
a) MiniMenu: Then after rebooting, MiniMenu will still be caught in an endless loop! Therefore boot up from an auxilary/temporary volume rather than your volume with the damaged MiniMenu! If your ruined system is on the NAND boot from an SD card, if the ruined system is on SD card, boot from NAND or another SD card. In doubt read: http://pandorawiki.org/Running_Linux_from_an_SD_card
b) Other than MiniMenu such as XFCE: Then you are lucky. Simply start into XFCE, and continue with the next step.
2) Open ~/.mmpref.conf with a text editor and set the variable filesystem.do_pnd_disco to the value 1.
3) Reboot into your healed volume. |
|
259 | Core | Bug Report | High | Hold switch does NOT lock keyboard! Especially crucial ... | Closed | |
Task Description
Apps, which operate with the Pandora in closed lid mode, such as audio players, server processes, etc, in a button-press-probably environment (as i.e. your pocket) still CAN receive the shoulder button L + R key presses, and if they have a meaning in these programs, they could trigger undesired actions.
And also in the current implementation of the Low Power Mode (See: FS#260) key presses may still be received.
Therefore I strongly propose to implement the HOLD switch to en/dis-able a keyboard lock.
IN DETAIL: This shall be global, meaning that the input processing software (however this is implemented on the Pandora: kernel, driver, … ) keeps the lock state (on/off), and if the keyboard state is off,
a) discards all input, or
b) if it makes sense for some reason/applications (any ideas?) just writes them into a queue/buffer, which gets (partially) executed or made accessible to certain software after the keyboard gets unlocked again.
FYI: I have tested the hold switch with the Pandora Input-Tester, and it is recognized. So my report is definitely a software (and not an hardware) issue. |
|
255 | Core | Bug Report | Medium | Waking Pandora with closed lid nevertheless turns scree ... | Closed | |
Task Description
Steps to reproduce the undesired behavior:
1) Close the lid. The screen goes off.
2) Slide the power switch to the right. The device goes into low power mode. The screen remains off.
3) Slide the power switch to the right. The device goes into normal power mode and turns on the screen although the lid is still closed!
Desired behavior:
Ad 3) If the system catches the event "wake from low power mode" it should first wake the system, then check the "lid open/close state", and set the screen on/off state accordingly. By this you could use the Pandora as a power-efficient sleep/wake-able closed-lid-device, practical for i.e. audio applications.
I am using: Pandora OS R1.HF6.A4 |
|
254 | Core | Bug Report | High | Several apps leave graphical artefact overlay (ghost) a ... | Closed | |
Task Description
After quitting some apps, their last graphical output remains on the screen, which covers a large area of the Pandora, and therefore makes it quite unusable, so that only a full restart resolves this issue.
As this happens in many apps (Mednafen-GB, Dark Light Battles, etc) this must be a problem within a shared library (driver, graphics lib, window manager framework, or similar). |
|
249 | Application | Bug Report | High | File Browser Thunar - After 2 nub double-clicks unreact ... | Closed | |
Task Description
If I navigate via keyboard (KEY UP/DOWN to move in lists, ENTER level down, BACKSPACE level up) I experience no problems at all. I can go many levels up/down, change to other folders, etc. No problems.
But if I navigate with the nubs, and using the right-nub-up-direction to trigger a double click, this only works 1-2 times, and from then on, the files/folders in Thunar cannot be clicked any further. I am stuck then.
A look into dmesg reveals this:
keyboard.c Can't emulate rawcode for keycode 139
The timestamp of that specific keyboard.c error messages exactly correlates with the bug occurrence times. (uptime timestamps matched with dmesg timestamps)
I tried alternative filebrowsers such as emelFM2, and there the problem does not exist, meaning I can trigger as many double clicks I want!
I am using HotFix 5 Alpha 4 on an SD card. The bug already annoyed me on a HF5 on the NAND. |
|
248 | Core | Feature Request | Medium | Support for hibernation by caching to SD card | Closed | |
Task Description
It would be very desirable that the PandoraOS could hibernate, and that this action can easily be accessed/triggered with either a hotkey or as an action for the max-idle-time-event or lid-close-event.
That would be the battery friendly universal action to quickly pause/resume any arbitrary application/task.
The current standby mode is far to power consuming for breaks longer than ~ 1 hour. Improving standby mode to be more battery-friendly would of course be too highly appreciated and practical.
If hibernation is triggered, RAM content gets written to a special file or partition on a SD card. The boot-manager of course needs to recognize such a RAM-file on SD-cards. In case it finds more than 1, i.e.: multiple cards/partitions, the one with the newest timestamp gets priority.
256MB RAM with about 10-20 MB/s read/write time to SD, would result in 25-12 seconds for going into or out of hibernation, which would be acceptable for me. In practice it would mean, that if I quickly have to pause me OpenPandora operation (i.e. train stop), I just close my lid, and put the Pandora into my pocket (2-4 seconds), and I am then trusting that the rest reliable happens in my pocket (10-20 seconds). |
|
247 | Core | Bug Report | Low | pnd_make.sh can't handle PND with spaces in the path | Closed | |
Task Description
pnd_make.sh can't handle PND with spaces in the path. For example, if the label of the volume where the PND is saved, has spacebars.
The Problem is line 655:
655: PND=$(readlink -f $PND)
Bash handles a path with spacebars as two seperate arguments for the readlink command.
The problem is, that i don't know a solution for this problem. |
|
245 | Core | Feature Request | Low | BugTracker: Submitter shall be able to edit bug after p ... | Closed | |
Task Description
I accidentally posted a "feature request" as a "bug report" within the FlySpray BugTracker.
I wanted to correct my mistake.
It was not possible to edit it.
I assigned the bug to myself.
Then I could edit it.
But now I cannot un-assign it from me.
I merely wanted to suggest a feature but not take development responsibility (yet).
For original submitters, who later realize a mistake in their post, there should be a possibility to correct their mistake.
Please un-assign me from #237 #241 #243 and this one #245. Thanks. |
|
241 | Application | Feature Request | Low | MiniMenu shall remember state for next start | Closed | |
Task Description
With the setting "Live (not exit) on app run?" set to "NO" the currently selected tab and item shall be remembered, so that you return to the same state, in which you left MiniMenu. |
|
235 | Core | Bug Report | Low | File /tmp/currentuser cannot be deleted by other users | Closed | |
Task Description
The system creates a file /tmp/currentuser at the first login of a user. After logging out and in as another user the file still contains the previous user name. An cannot be deleted/overwritten by the new user.
Steps To Reproduce:
At least two users are available and have XFCE GUI enabled.
1. Login as user (eg. guest), a file /tmp/currentuser is created (containing guest)
2. Log out
3. Log in as another user (eg. jgeiss), the file still contains the old name
4. Change GUI to PMenu
5. Log out
6. Log in as first user (guest)
Now the first user (guest) has PMenu as GUI which was set by the second user (jgeiss).
Maybe the permission should be 0666 for this file? |
|
233 | Core | Bug Report | Very Low | op_power.sh: errors | Closed | |
Task Description
op_power.sh gives some errors to me... it works anyway, but it's not nice to see them all the time.
/usr/pandora/scripts/op_power.sh: line 60: [: 5380: binary operator expected
or
/usr/pandora/scripts/op_power.sh: line 60: [: too many arguments
I guess line 60 of op_power.sh
if [ ! $wlstate ]; then
should rather be
if [ -z "$wlstate" ]; then
shouldn't it?
The same thing is in line
Then sometimes also
rm: cannot remove `/tmp/wlstate': No such file or directory
or
cat: /tmp/wlstate: No such file or directory
which could easily be fixed by adding a test -f /tmp/wlstate && or something like that before the respective command. I just added a lot of test, I'm not sure if every single one of them is really needed, but better too much than not enough, I would say. :-)
I can't attach a file (I click the button and nothing happens), so I just paste it there: http://nopaste.info/2256365eba.html
It's a bit longer because some indentations were wrong (and I corrected them) and I changed all indentations to tabs = 8 spaces instead of 2. |
|
232 | Core | Bug Report | Low | HF6 - charged completed with lid closed causing keyboar ... | Closed | |
Task Description
HF6 - It seems as when charging finishes with pandora on then charge light goes out (charge completed assuming) keyboard not functioning just gamepad. Can't use letters to cycle through in mini minimenu or use space to pull up ovr settings.
Will test further |
|
231 | Core | Bug Report | Low | Touchscreen not accurate on the edges - Calibration doe ... | Closed | |
Task Description
The touchscreen is accurate in the middle of the screen but precision is off by one or more mm near the edges of the screen. Recalibrating and rebooting does not help.
Seems like this is just a permission problem - tslib saves calibration data to /etc/pointercal which is noch writeable for the regular user.
Changing permission on that file to 666 solves this, but i guess starting the calibration tool with root permission (gksu?) would be a better solution. |
|
230 | Core | Bug Report | Low | Second SD slot not working in future kernel version 2.6 ... | Closed | |
Task Description
Sorry, not sure where to log this bug. I have confirmed with aTc on freenode, that SD slot #2 does not work on kernel version 2.6.37 from the openpandora git.
Happy to test anything and reports results. |
|
228 | Core | Bug Report | Low | libpnd must be linked to libstdc++ | Closed | |
Task Description
Run "ldd -r /usr/lib/libpnd.so.1", and a number of undefined symbols are listed. These become a problem when attempting to load libpnd in Python. I imagine it could be a problem when attempting to load libpnd in other languages as well.
This can be worked around with "LD_PRELOAD=/usr/lib/libstdc++.so" before running a Python program that loads libpnd.
But it can be worked around more easily by linking libstdc++ during compile. Adding "-lstdc++" to line 41 of libpnd's Makefile does it. I'd add a patch, but the attach file button isn't working for me. Still, a simple fix, right? |
|
226 | Core | Feature Request | High | Boot from /dev/sda devices requested | Closed | |
Task Description
Boot from usb hard disk not supported. This should be a rather simple fix of adding the sdx devices and adjust the boot scripts??
I was able to put this autoboot.txt on mmc 0:1
setenv bootargs debug root=/dev/sda1 rw rootdelay=2 console=ttyS0,115200n8 vram=6272K omapfb.vram=0:3000K
ext2load sda 0:1 0x80300000 /boot/uImage
bootm 0x80300000
This failed with amongst other things "Block device sda 0 not supported" and something about failing to load kernel
So I then changed the autoboot file to this
setenv bootargs debug root=/dev/sda1 rw rootdelay=2 console=ttyS0,115200n8 vram=6272K omapfb.vram=0:3000K
ext2load mmc 0:3 0x80300000 /boot/uImage
bootm 0x80300000
All this did was die after the kernel loaded.
I believe I could much better make use of this device if I could boot from some faster storage, please advise :) |
|
224 | Core | Bug Report | Low | Unresponsive start menu since HF5 | Closed | |
Task Description
Since hotfix 5, the start menu often pauses for a few seconds, not letting me select anything or move the mouse.
Other people have reported the issue as well:
http://boards.openpandora.org/index.php?/topic/2295-is-the-xfce-menu-trolling-anyone-else/page__gopid__42559#entry42559 |
|
221 | Core | Bug Report | Medium | 32MB worth of qt4 examples in /usr/bin/qt4 ? | Closed | |
Task Description
Hi, after upgrading to HF5, I accidentally discovered that there are 32MB of qt4 examples & demos in directory /usr/bin/qt4, those examples do work. For instance the /usr/bin/qt4/examples/webkit/fancybrowser/fancybrowser is a working WWW browser.
It is, without any dispute a very useful qt4 development help, but are you sure that you want to include all that in NAND ? |
|
220 | Core | Feature Request | Low | Please include /usr/bin/xkbset | Closed | |
Task Description
One of the first things after installing HF5 was downloading xkbset, because it is necessary for proper L-R buttons mapping as mouse buttons. Could you please include that in the system?
I am using urjaman's executable from here:
http://www.gp32x.com/board/index.php?/topic/55124-remapping-the-mouse-buttons-etc/page__st__15__p__896576&#entry896576
Even better would be a GUI that allows mapping of L-R buttons for mouse, just like GUI for nubs :) But including xkbset will be already good. |
|
215 | Core | Bug Report | Medium | Kingston 32GB Class6G2 SDHC card not working in pandora | Closed | |
Task Description
I have noticed errors like this, but not every time
[ 1455.612792] mmc2: card claims to support voltages below the defined range. These will be ignored.
[ 1455.621795] mmc2: SDIO card claims to support the incompletely defined 'low voltage range'. This will be ignored.
[ 1455.665985] mmc2: new SDIO card at address 0001
This is me plugging in my 32GB SD6G2 Kingston SDHC card.
at [ 1114.484252] is when the file copy started
Errors continue from there until it bombs and remounts the filesystem readonly.
I have tried this with ext3 vfat in various configurations and all fail the same I/O errors
Let me know if I can do anything to help
-------------------------------------
[ 989.496459] mmc1: host does not support reading read-only switch. assuming write-enable.
[ 989.504638] mmc1: new high speed SDHC card at address 0003
[ 989.510620] mmcblk1: mmc1:0003 SD32G 31514112KiB
[ 989.515625] mmcblk1: p1 p2 p3 p4 < p5 p6 >
[ 989.940490] FAT: invalid media value (0x00)
[ 989.944702] VFS: Can't find a valid FAT filesystem on dev mmcblk1.
[ 990.083190] FAT: invalid media value (0x00)
[ 990.087402] VFS: Can't find a valid FAT filesystem on dev mmcblk1.
[ 991.907562] EXT3-fs: Unrecognized mount option "umask=0" or missing value
[ 991.922943] EXT3-fs: Unrecognized mount option "umask=0" or missing value
[ 992.002563] mmci-omap mmci-omap.0: MMC IRQ 0x208002 : TC ERRI DCRC
[ 992.003143] mmcblk0: retrying using single block read
[ 992.028411] kjournald starting. Commit interval 5 seconds
[ 992.048553] EXT3-fs: Unrecognized mount option "umask=0" or missing value
[ 992.092346] kjournald starting. Commit interval 5 seconds
[ 992.237091] kjournald starting. Commit interval 5 seconds
[ 992.259185] EXT3-fs: Unrecognized mount option "umask=0" or missing value
[ 992.361999] FAT: bogus number of reserved sectors
[ 992.366760] VFS: Can't find a valid FAT filesystem on dev mmcblk1p4.
[ 992.400909] kjournald starting. Commit interval 5 seconds
[ 992.612945] EXT3 FS on mmcblk1p2, internal journal
[ 992.617797] EXT3-fs: mounted filesystem with ordered data mode.
[ 992.787475] EXT3 FS on mmcblk1p3, internal journal
[ 992.792449] EXT3-fs: mounted filesystem with ordered data mode.
[ 993.038940] EXT3 FS on mmcblk1p1, internal journal
[ 993.043884] EXT3-fs: mounted filesystem with ordered data mode.
[ 993.205749] EXT3 FS on mmcblk1p5, internal journal
[ 993.210632] EXT3-fs: mounted filesystem with ordered data mode.
[ 993.510253] FAT: bogus number of reserved sectors
[ 993.515045] VFS: Can't find a valid FAT filesystem on dev mmcblk1p4.
[ 1114.484252] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1114.484802] mmcblk0: retrying using single block read
[ 1115.763946] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1115.765594] mmcblk0: retrying using single block read
[ 1115.984649] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1115.984985] mmcblk0: retrying using single block read
[ 1116.039489] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.039916] mmcblk0: retrying using single block read
[ 1116.094329] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.094757] mmcblk0: retrying using single block read
[ 1116.150146] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.152343] mmcblk0: retrying using single block read
[ 1116.212127] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.212615] mmcblk0: retrying using single block read
[ 1116.267791] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.268280] mmcblk0: retrying using single block read
[ 1116.335723] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.337738] mmcblk0: retrying using single block read
[ 1116.410766] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.413360] mmcblk0: retrying using single block read
[ 1116.488250] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.490234] mmcblk0: retrying using single block read
[ 1116.581390] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.581939] mmcblk0: retrying using single block read
[ 1116.645721] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.646331] mmcblk0: retrying using single block read
[ 1116.933288] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.933715] mmcblk0: retrying using single block read
[ 1117.000518] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.002899] mmcblk0: retrying using single block read
[ 1117.068328] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.070526] mmcblk0: retrying using single block read
[ 1117.128326] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.128753] mmcblk0: retrying using single block read
[ 1117.194183] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.194488] mmcblk0: retrying using single block read
[ 1117.261566] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.262084] mmcblk0: retrying using single block read
[ 1117.328674] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.329956] mmcblk0: retrying using single block read
[ 1117.388061] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.390380] mmcblk0: retrying using single block read
[ 1117.451629] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.452087] mmcblk0: retrying using single block read
[ 1117.510467] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.512725] mmcblk0: retrying using single block read
[ 1117.714874] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.715301] mmcblk0: retrying using single block read
[ 1117.776550] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.778930] mmcblk0: retrying using single block read
[ 1117.841247] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.841674] mmcblk0: retrying using single block read
[ 1122.718658] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1122.719055] mmcblk0: retrying using single block read
[ 1123.265136] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1123.265441] mmcblk0: retrying using single block read
[ 1123.442230] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1123.442413] mmcblk0: retrying using single block read
[ 1126.759338] mmci-omap mmci-omap.1: MMC IRQ 0x108000 : ERRI DTO
[ 1126.759399] mmcblk1: error -110 transferring data, sector 32669824, nr 8, card status 0xc00
[ 1126.807830] mmci-omap mmci-omap.1: MMC IRQ 0x108000 : ERRI DTO
[ 1126.807891] end_request: I/O error, dev mmcblk1, sector 32669824
[ 1126.813934] Buffer I/O error on device mmcblk1p1, logical block 4083726
[ 1126.820556] lost page write due to I/O error on mmcblk1p1
[ 1127.630950] mmci-omap mmci-omap.1: MMC IRQ 0x108000 : ERRI DTO
[ 1127.631011] mmcblk1: error -110 transferring data, sector 32686232, nr 8, card status 0xc00
[ 1127.715179] mmci-omap mmci-omap.1: MMC IRQ 0x108000 : ERRI DTO
[ 1127.715240] end_request: I/O error, dev mmcblk1, sector 32686232
[ 1127.721282] Buffer I/O error on device mmcblk1p1, logical block 4085777
[ 1127.727935] lost page write due to I/O error on mmcblk1p1
[ 1133.399963] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1133.400024] Spurious DMA IRQ
[ 1133.403411] mmcblk0: retrying using single block read
[ 1133.504821] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1133.504943] mmcblk0: retrying using single block read
[ 1133.599304] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1133.599548] mmcblk0: retrying using single block read
[ 1133.767486] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1133.767578] mmcblk0: retrying using single block read
[ 1134.222564] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1137.074981] mmcblk0: retrying using single block read
[ 1137.465576] mmci-omap mmci-omap.1: MMC IRQ 0x108000 : ERRI DTO
[ 1137.465667] mmcblk1: error -110 transferring data, sector 17316672, nr 72, card status 0xc00
[ 1137.509582] mmci-omap mmci-omap.1: MMC IRQ 0x108000 : ERRI DTO
[ 1137.509643] end_request: I/O error, dev mmcblk1, sector 17316672
[ 1137.515686] end_request: I/O error, dev mmcblk1, sector 17316680
[ 1137.521728] end_request: I/O error, dev mmcblk1, sector 17316688
[ 1137.527770] end_request: I/O error, dev mmcblk1, sector 17316696
[ 1137.533813] end_request: I/O error, dev mmcblk1, sector 17316704
[ 1137.539855] end_request: I/O error, dev mmcblk1, sector 17316712
[ 1137.545867] end_request: I/O error, dev mmcblk1, sector 17316720
[ 1137.551910] end_request: I/O error, dev mmcblk1, sector 17316728
[ 1137.557952] end_request: I/O error, dev mmcblk1, sector 17316736
[ 1137.766906] Aborting journal on device mmcblk1p1.
[ 1137.997436] journal commit I/O error
[ 1138.001037] EXT3-fs error (device mmcblk1p1) in ext3_create: IO failure
[ 1138.225067] ext3_abort called.
[ 1138.228149] EXT3-fs error (device mmcblk1p1): ext3_journal_start_sb: Detected aborted journal
[ 1138.236785] Remounting filesystem read-only |
|
214 | Core | Bug Report | High | op_wifi pnd not exiting cleanly, with fix (one characte ... | Closed | |
Task Description
The op_wifi pnd does not exit out cleanly once the encased script executes,
the pndrun_op_wifi.out reports
umount: /mnt/utmp/op_wifi: device is busy.
umount: /mnt/utmp/op_wifi: device is busy.
umount UNION failed, didn't clean up. Process still using this FS :
3197 ? S 0:00 /bin/sh /etc/init.d/wl1251-init start
This op_wifi.sh just calls
/usr/pandora/scripts/op_wifi.sh
for some reason, the init.d/w.... start causes it to hang, I executed all this locally, and it doesn't appear to keep running
Appending " &" to the line which calls this init script, solves the problem. |
|
213 | Application | Bug Report | Low | Gigolo does not perform it's task | Closed | |
Task Description
In it's current state, Gigolo is flat out broken and (almost) useless. It pretends to to it's job, but can't because it's missing critical pieces of anatomy.
It can mount local filesystems correctly, but then so can thunar, so this is a redundant and useless function. The main reason to use Gigolo is to mount remote filesystems easily, and without having to use the terminal, and to save passwords in your keychain.
The solution to the problem is to perform the following tasks:
sudo opkg install gvfsd-sftp sshfs-fuse
sudo mousepad /etc/modutils/fuse
type "fuse" save and quit
sudo update-modules |
|
212 | Core | Feature Request | Low | Add curl to core installed programs | Closed | |
Task Description
I wish for curl to be installed by default on the upcoming pandora FWs,
As reported by the angstrom repo, where I install using the command:
$sudo su
...
#opkg update
#opkg install curl
curl 7.21.2-r4.0.9 is 78.57 Kilobytes with the dependencies
Depends:libcurl4, libgnutls26, libgcrypt11, libgpg-error0, libc6, libz1
I do not know which is installed by default, but I'm sure libc6 is, so I'm going to state the info on the rest of the packages for its memory space usage on the NAND
libcurl4(142.99 Kilobytes):
Command line tool and library for client-side URL transfers.
Depends:libc6, libgnutls26, libz1, libgcrypt11, libgpg-error0, as you can see, it has the same dependencies as above, so it seems both curl and libcurl are probably exclusive from the others, but I will go forward and state the rest of the dependencies
libgnutls26 2.8.6-r10.0.5 (291.44 Kilobytes)
Depends:libz1, libgcrypt11, libgpg-error0, libc6, (again, it looks like the above depends on this)
libgcrypt11 1.4.1-r0.9 (220.35 Kilobytes)
Depends: libgpg-error0, libc6, (Oh look, we're not looking at libz1 anymore)
libgpg-error0 1.4-r7.1.9 (5.78 Kilobytes)
Depends:libc6
now to the lone libz1
libz1 1.2.3-r7.0.9 (41.95 Kilobytes)
Depends:libc6
So, in the case we already have the gpg stuff, then the installation is only 221.56KB, however, with the zlib and the gpg included, the total comes to 781.08KB
So, now that the cost is out of the way, What are the goods and bads?
Good:
Its a very versatile CLI program to get and send information over http through the network, and is tolerant of network issues
It doesn't take too much space relative to things that have been pulled out, like abiword.
The libcurl is a very good library, and could be of great benefit to some future projects.
Bad:
Well, we already have wget, which is not as configurable, and wget hates Craig's appstore
Here's the link to curl on the repo
http://www.angstrom-distribution.org/repo/?pkgname=curl |
|
211 | Core | Bug Report | Low | x11vnc server (in xfce menu - > network) does not work! | Closed | |
Task Description
x11vnc launcher in xfce menu -> network does not work.
can this be fixed please. |
|
208 | Core | Bug Report | Critical | HOTFIX 4 and 5 Slow WIFI | Closed | |
Task Description
I'm getting 5kb/s with bursts up to 10kb/s if I am lucky.
I have attempted every channel on my router.
Tried every encryption even no encryption.
Tested with the router's wifi speed: 300Mbps 154Mbps and 45Mbps
I'm running Hotfix 5 RC2.
Wifi works fine with my android smartphone, and other wireless devices such as a laptop. |
|
207 | Core | Bug Report | Medium | Touchscreen calibration / use of nubs conflict | Closed | |
Task Description
When using certain apps like Basilisk 2 / Dosbox / Enigma the analogue stick and touchscreen are both available to use as a mouse cursor.
All is well with the touch until you decide to touch the analogue stick when then affects touchscreen alignment by about 2 - 3 CM.
This has been going on since first release. |
|
205 | Core | Bug Report | Medium | libpnd functions and dynamic libs missing | Closed | |
Task Description
tried to compile a simple test application that uses functions from libpnd, namely
pnd_evdev_open(pnd_evdev_e)
pnd_evdev_dpad_state(pnd_evdev_e)
pnd_evdev_closeall()
but all 3 seem to be missing.
yes, i'm linking to libpnd ... but no chance to get it running.
i'm using ivanovic's latest toolchain, which in turn installs "pandora-libpnd-dev_1.0-r40.5_armv7a.ipk" ...
also, there's only the static library available inside, no dynamic libraries. |
|
203 | Core | Bug Report | Low | Video-out setting window does not exit on OK | Closed | |
Task Description
The "video-out" window opens again if you choose OK button. |
|
202 | Core | Bug Report | Low | Set Date and Time won't let you cancel or close | Closed | |
Task Description
The Date and Time application in MiniMenu by won't let you use the cross or the cancel button to close the application without changing anything.
If you use one of those buttons then a new window opens that says: "Error: Please select a timezone" and equally so for the date and time. |
|
200 | Core | Bug Report | Low | After opening the lid, the backlight is not reset to th ... | Closed | |
Task Description
Using the hotkeys to set the backlite, after closing and then opening the lid, the backlight is not reset to the same level it was before closing it.
It seems to set it to a fixed value. |
|
198 | Application | Bug Report | Low | Mousepad: 'Find' works only once | Closed | |
Task Description
Mousepad 0.2.16
Find (Ctrl+F) works once, the next time it is used the button 'Find' is and stays grayed out. |
|
197 | Core | Bug Report | High | [PATCH] Fix opp if booting with wrong settings in hw | Closed | |
Task Description
Hi,
This should help with cases like this
http://www.gp32x.com/board/index.php?/topic/57303-overclocking-broke-my-pandora/
Patch attached. |
|
196 | Core | Feature Request | Medium | [PATCH] Add tablet support into kernel | Closed | |
Task Description
Hi,
This should be a quite simple thing, but my first time touching
the OE repo and i cant test it, so be careful. |
|
195 | Core | Feature Request | High | Start re-recharge of battery sooner | Closed | |
Task Description
Increase battery LVL_4 and LVL_3 threshold.
After reaching 100%, in some cases the charge circuit enters "battery full" state, stops charging, and begins to discharge. This is not entirely unexpected behavior according to the spec sheet, although I don't fully understand exactly the situations in which it completes charging. Once the battery is full, the battery will begin discharging. The charge circuit automatically restarts the recharge once the voltage has gone below a certain level (crosses below the LVL_3 voltage threshold)
The default LVL_3 voltage threshold is 3.902 volts which is at about 80-85% battery level as recorded by bq27500 chip. In my opinion, this is way too low.
Setting the BCIMFTH2 register to 0xCB increases the voltage threshold to about 4.003 volts which is about 93%.
Setting it to 0xDC may also be worthwhile, which is just over 95%.
By default, if a user leaves their Pandora plugged in overnight, they may wake up to find their Pandora has stopped charging and the capacity has dropped to almost 80%, which can be quite startling to some users who will then report it as a bug.
This change will ensure that it never drops below 93-95%, a much more acceptable level.
Specific code changes suggested, in the /drivers/power/twl4030_bci_battery.c file, somewhere in the twl4030_bci_battery_probe function (or a function called by it), add the lines:
/********************************/
#define KEY_FTH2 0x7F
#define REG_BCIMFTH2 0x017
ret = twl4030_i2c_write_u8(TWL4030_MODULE_MAIN_CHARGE, KEY_FTH2, REG_BCIMFKEY);
if (ret)
return ret;
ret = twl4030_i2c_write_u8(TWL4030_MODULE_MAIN_CHARGE, 0xDC, REG_BCIMFTH2);
if (ret)
return ret;
/********************************/
(Move defines to the top, as appropriate) |
|
194 | Core | Bug Report | Low | python ctypes broken (and fix) | Closed | |
Task Description
run python and type import ctypes
cant find _ctypes it says....
for further details and a fix see
http://www.gp32x.com/board/index.php?/topic/57102-python-ctypes-stopped-working/ |
|
193 | Core | Bug Report | Low | Cannot reach button well in ubuntu x64 | Closed | |
Task Description
Window can also not be resized |
|
192 | Core | Bug Report | Medium | [U-Boot] ext2fs_devread() read error - block (boot from ... | Closed | |
Task Description
[U-Boot] ext2fs_devread() read error - block
Description:
Formatted two different Transcend 8GB SD cards as EXT2 using both GParted and also with Mkfs.ext2, extracted pandora-rootfs.tar.bz2 to the root of the SD and added 'autoboot.txt' as described here: http://openpandora.org/firmware/README.txt
This issue appears to be same as mentioned here, looks like a patch maybe required in drivers/mmc/omap3_mmc.c):
http://lists.denx.de/pipermail/u-boot/2010-June/072198.html
Output on boot :
mmc1 is available
reading autoboot.txt
** Unable to read "autoboot.txt" from mc1 0:1 **
Loading file "autoboot.txt" from mmc1 device 0:! (xxa1)
184 bytes read
** Executing plain script at 82000000
Loading file "/boot/uImage-2.6.27.46-omap1" from mmc device 0:1 (xxa1)
** ext2fs_devread() read error - block
** Unable to read "/boot/uImage-2.6.27.46-omap1" from mmc 0:1 **
## Booting kernel from Legacy Image at 8030000 ...
Image Name: Angstrom/2.6.27-pandora+r21+git4
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2325740 Bytes = 2.2 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... Bad Data CRC
ERROR: can't get kernel image!
syntax error |
|
189 | Core | Bug Report | Medium | pnd-run.sh does not work correctly for very long <pathn ... | Closed | |
Task Description
When unmounting, the pnd-run-script greps the output of "losetup -a" at some point. But if you have a very long pathname and filename for the pnd (like "/media/trans8/gamedata/scummvm/Secret_of_Monkey_Islands_Amiga_EN.pnd" then the endpart is cut off in the output, grep can't find the right part and the script get's confused.
Example:
mounting works:
/usr/pandora/scripts/pnd_run.sh -p /media/trans8/gamedata/scummvm/Secret_of_Monkey_Islands_Amiga_EN.pnd -b scummvm -m
unounting does not work:
/usr/pandora/scripts/pnd_run.sh -p /media/trans8/gamedata/scummvm/Secret_of_Monkey_Islands_Amiga_EN.pnd -b scummvm -u
(see /tmp/pndrun*-logs for output)
The problem is that the outut of losetup looks like this in such a case:
"/dev/loop7: [b309]:157081 (/media/trans8/gamedata/scummvm/Secret_of_Monkey_Islands_Amiga_*)"
And because the pnd-name is not fully shown, grepping the name does not work. After i renamed th pnd to a much shorter name (somi_amiga_en.pnd) it worked nicely. Still this should be fixed. |
|
188 | Core | Bug Report | High | "rdate" sets the time exactly 3 hours in advance | Closed | |
Task Description
"rdate -s time.ien.it" will set the date (hour) 3 hours in advance.
The time (and timezone) can be adjusted manually using the "Settings -> Date and Time" tool, but on the next rdate-update the issue will occur again |
|
187 | Core | Bug Report | High | LCD turns off after "rdate" updated the date | Closed | |
Task Description
running "sudo rdate -s time.ien.it" will set the brightness of the LCD to 0.
User has to use FN + I to increase it back to a usable level.
"rdate" asks for the super-user password as expected, updates the date as expected, but turns off the screen. |
|
186 | Application | Bug Report | Medium | unusable "Manage LCD Gamma" tool | Closed | |
Task Description
Pandora Menu -> Settings -> LCD-Settings -> Manage LCD Gamma
Removing all the profiles listed there will make the user unable to even create a new one. The tool becomes unusable. I hope a re-flash would fix the problem.
The last profile in the list, or the Default one, shouldn't be deletable at all. |
|
184 | Core | Feature Request | Medium | libpnd: Add a function to get all mounted PNDs | Closed | |
Task Description
Add a function to get all mounted PNDs. Because it's very annoying to check all the menu/desktop folders on all of the SD-Cards. |
|
183 | Core | Bug Report | High | Left mouse click and hold = fail | Closed | |
Task Description
When I want to hold and select multiple files its not working. Not with the nubs or the touchscreen.
I can try an easy test by making the select rectangle on the desktop. It only becomes very very tiny. If I try very fast diagonal drag motion on the touchscreen. It becomes a little larger.
Trying to grab scrollbar is the same issue. |
|
182 | Core | Bug Report | Medium | Ctrl + F5 (Fn Lock) Fail | Closed | |
Task Description
So I've tried this a while now with no success. I'm assuming its when Fn is triggered and then pressing Ctrl or Alt it goes away. |
|
181 | Application | Bug Report | Low | Triple click in Thunar crash | Closed | |
Task Description
Triple tapping (with the stylus) a directory in Thunar in icon or compact mode (not detail view) causes Thunar to close (crash)
This is consistently repeatable: tapping three times in rapid succession on the same spot of the file causes the crash. It must be the exact same spot, as if double clicking, but a third tap is added. This can be triggered especially when a user becomes frustrated at mistapping, gets carried away, and taps too much. |
|
180 | Core | Bug Report | Medium | LCD Brightness Lower = Flashing, Dies. | Closed | |
Task Description
Just try and lower with the Fn+Br- until it starts to flashing and just dies if you go lower. It does go back if you raise it again. Feels wrong. Also no real feel in the brightness getting lower. |
|
177 | Core | Bug Report | Medium | no x or xfce after shutdown and reboot | Closed | |
Task Description
often but not always after shutting down the system (xfce logout, choose shutdown) there´s a problem when booting again.
i got the normal bootscreen but when x an xfce should start the screen remains black. i cannot say if the x or xfce didn´ start or if it is a problem with the backlight intensity.
rebooting with pandora key and power key leads to the same situation. the only thing that seems to help is to remove the battery shortly.
so, what is the difference beetween reboot after powerdown and reboot after replacing the battery? there could be the point to fix this problem. |
|
174 | Base OS | Feature Request | Low | Include modem-manager in base image | Closed | |
Task Description
Please consider including the modemmanager package in the base distibution.
This allows 3G wireless dongles to work out of the box (configured via network-manager). |
