|
134 | Core | Bug Report | Low | please add a working phonon backend | Closed | |
Task Description
Please see : http://www.gp32x.com/board/index.php?/topic/54831-minitube/page__view__findpost__p__883993
:) |
|
136 | Core | Bug Report | High | rather high battery discharge while Pandora is powered ... | Closed | |
Task Description
The Pandora does seem to use too much energy while it is turned off. A testcase: The pandora was turned off over night (about 8 hours) and battery state dropped from 98% to 96%. When removing the battery from the pandora for the same amount of time, the state is not changed at all.
This is based on the zaxxon firmware release with hotfix3, beta2.
Problem: if you don't use the pandora for a while and forget to remove the battery you can cause a deep discharge which might damage the battery. This is also a problem if the Pandora does eg shutdown itself since power is out and you can't directly attach it to a charger.
Possible causes:
* Design fault in the board.
* Too much powered on while the device *should* be completely powered off. The only things that should get power are the clock and the power button. This should basically not drain much.
Regarding the clock: The PalmPre is based on the OMAP3, too. There you basically have no discharge when it is powered off, so it is unlikely that the fault is in the OMAP3 itself. |
|
139 | Base OS | Bug Report | Low | Space should not be accepted in hostname | Closed | |
Task Description
http://www.gp32x.com/board/index.php?/topic/54878-embarassingly-nooby-questions-from-a-new-pandora-owner/page__view__findpost__p__885235
If the user names their Pandora using a space in the name, "This will prevent Xfce from operating correctly". Should trap this when asking for a host name. |
|
141 | Base OS | Bug Report | High | When using an unlabeled SD card, Hotfix3 final can't un ... | Closed | |
Task Description
I had beta 1 of hotfix 3, and there turning the pandora into a cardreader worked fine for that card. However, I just installed the latest hotfix 3 final, but that one fails to unmount. Attached is the pndrunop_storage.out. Apparently something's going wrong with the splitting of the partition name, as it tries to unmount /dev/mmcblk0 instead of /dev/mmcblk0p1
Manually unmounting it by using sudo umount /dev/mmcblk0p1 does work, but then I can't use the tool because that apparently only lists mounted memorycards. |
|
143 | Core | Bug Report | Low | LED triggers timer and heartbeat cause freezing when us ... | Closed | |
Task Description
Summary is about all i can dug out now. Somehow related to the PWM driving, because SD, bt and wifi leds work with trigger=timer.
NOTE: power and charger leds are driven by PWM (just so you all know what I'm talking about).
All i wanted to do was to add blinking power led to low power mode and all i get is a frozen pandora :/. |
|
144 | Core | Bug Report | Low | Wifi LED does not always get re-activated after enablin ... | Closed | |
Task Description
Wifi LED does not always get re-activated after enabling wifi.
It seems that the led trigger which ought to be set to [phy0dadio] no longer exists and the phy# seems to increment (up to at least 11 I have observed)
If I set the trigger to phy##radio then the notification works again, but I'm not sure of the best way to fix this. I suppose a quick hack to the wl1251-init script is the place to start. |
|
146 | Base OS | Bug Report | High | Minimenu regressions with Hotfix 3 | Closed | |
Task Description
Fresh firmware install with Hotfix 3 installed results in the following issues with Minimenu.
1. 25+% cpu usage versus ~5% in earlier versions.
2. Touchscreen no longer works correctly to select icons. Selecting tabs still works and occasionally it will work for selecting an application icon, but for the most part it simply does nothing. |
|
147 | Base OS | Bug Report | Low | Screen backlight is ON when starting with lid closed | Closed | |
Task Description
[HotFix3 installed]
If you power up the Pandora and have the screen closed, the backlight will still go on. That should not happen. Right now you have to open it, close it and than the backlight turns off to save energy... |
|
149 | Base OS | Bug Report | Very Low | Resets if Battery is removed - but power is still pluge ... | Closed | |
Task Description
The Pandora resets if the battery is removed - even though its plugged to the AC Adapter.
the power disapears for a second, and then the pandora notices that the power cable is actually plugged in, and immediately starts the pandora again |
|
150 | Core | Bug Report | Low | pndnotifyd Segfault | Closed | |
Task Description
Might be related to http://bugs.openpandora.org/index.php?do=details&task_id=128
as it have exactly the same behaviours.
But this time no translation is involved (masked in my script until this is fixed).
And making the file smaller (by removing apps :( ) managed to let it alive, so it seam to be file size related. |
|
152 | Core | Bug Report | High | Data transfer issued between SD slot 1 and 2 | Closed | |
Task Description
It appears that any users are having trouble transferring files from SD cards in slot 1 to SD cards in Slot 2.
Full details here.
http://www.gp32x.com/board/index.php?/topic/55077-looks-like-the-is-a-readtiming-problem-with-sd-reading-when-high-cpu/ |
|
154 | Core | Bug Report | High | Vpn doesn't work | Closed | |
Task Description
When clicking on the Network Manager Applet Symbol, then selecting "VPN Connections" and then "Configure VPN", all the buttons in the following dialoge are greyed out. There is no way to add a new vpn connection. Restarting the system or deactivating the WiFi and then reactivaing it doesn't help. |
|
157 | Core | Bug Report | Low | Thunar and stilus | Closed | |
Task Description
With Thunar 1.1 and OS Zaxon (hotfix 3) :
- with detail view
- I open Thunar
- I click with the stilus to select the SD card
- I double click with the stilus to open a folder
=> click with the stilus doesn't select file/folder anymore
(I know it is a known bug, but it is not in the list) |
|
160 | Base OS | Bug Report | Low | bug in date/time setting window | Closed | |
Task Description
first time i changed the date/time with no problems afterward every time when i try to change it it gives me "Please select month ..." this happens after selecting the time zone window. |
|
162 | Core | Bug Report | Medium | XFCE Setting date | Closed | |
Task Description
The tool to setup the date/time in XFCE doesn't work properly :
- Menu -> Settings -> Date and Time
- The tool show up
- Select the time zone
Now an error window spam every seconds... |
|
163 | Base OS | Bug Report | Low | DPMS related "display problems" | Closed | |
Task Description
Currently it looks like DPMS is active in xorg (eg when using XFCE). DPMS is normally used for stuff like turning the screen off to save energy. There seems to be no way to configure this while in XFCE. So the default xorg server values are used.
At the moment the screen is turned off after 10mins of inactivity. Problems with this are
a) that the time till it is turned off can not be configured
b) after wakeup from such a DPMS related display shutdown the brightness is set to maximum.
Solution to this:
Deactivate the sleep values via xorg.conf. I am attaching a diff to "[openembedded.git] / recipes / xorg-xserver / xserver-xorg-conf / omap3-pandora / xorg.conf" changing those to "default off". |
|
164 | Core | Bug Report | Low | Display brightness not restored at booting, HF4beta3 | Closed | |
Task Description
The update from Hotfix3 to Hotfix4 beta3 broke restoring of display brightness at boot time. Restoring of brightness after "powersave mode" (aka flipping the power switch for a short time) does work nicely. This might be related to bug #163 ( http://bugs.openpandora.org/index.php?do=details&task_id=163 ) where shutting the display down via DPMS does result in the brightness being lost when getting the display on again.
This is related to the desktop mode (XFCE). Don't know if it does happen for minimenu, too, not tested yet. |
|
165 | Core | Bug Report | Low | VPNC does't work | Closed | |
Task Description
vpnc doesn't work |
|
168 | Core | Bug Report | Low | qt-embedded doesn't work | Closed | |
Task Description
qt-embedded doesn't work |
|
169 | Core | Bug Report | Low | pidgin freezes all the time | Closed | |
Task Description
pidgin freezes all the time |
|
172 | Core | Bug Report | Low | Angstrom repo's bison is borked (FYI) | Closed | |
Task Description
This is how it tries to call m4 (strace -fF'd):
[pid 4231] execve("/OE/angstrom-dev/sysroots/x86_64-linux/usr/bin/m4", ["/OE/angstrom-dev/sysroots/x86_64"..., "/usr/share/bison/m4sugar/m4sugar"..., "-", "/usr/share/bison/yacc.c"], [/* 38 vars */]) = -1 ENOENT (No such file or directory)
Problem = obvious.
This is here because a) it is the bison that i get with opkg install bison and b) because i could find a general purpose bugtracker for stuff in the angstrom repo with a single googling.
Added info on bison version, etc:
pandora:/media/mmcblk0p3/dev/avrdude-5.6# opkg info bison
Package: bison
Version: 2.3-r5.0.5
Depends: libc6
Provides:
Status: install user installed
Section: devel
Architecture: armv7a
MD5Sum: c8e62fa82a96e9bba4c014c4345062ed
Size: 181368
Filename: bison_2.3-r5.0.5_armv7a.ipk
Description: GNU Project parser generator (yacc replacement).
Installed-Time: 1283127122 |
|
173 | Core | Bug Report | High | X uses 100% cpu in low power mode | Closed | |
Task Description
After 10 minutes in low power mode X seems to go nuts and use 100% CPU. Obviously this is bad ;-) 14MHz isn't *that* slow, so there's obviously something getting wedged.
I haven't been able to figure out exactly what's happening, but the fact that it always occurs after exactly 10 minutes suggests its power management related. Maybe we're getting stuck trying to kick off the screensaver, or something?
Hacking op_power.sh do disable screen blanking shows that, unsurprisingly, the screen freezes at the same time X goes AWOL.
Pressing the power switch brings the device out of low power mode, though there is often a few seconds additional delay as the event handling scripts take longer than normal to run because the CPU is already busy.
I've attached the results of
top -b -d 60 > toplog &
while sleep 60 ; do cat /proc/loadavg; done > loadlog |
|
177 | Core | Bug Report | Medium | no x or xfce after shutdown and reboot | Closed | |
Task Description
often but not always after shutting down the system (xfce logout, choose shutdown) there´s a problem when booting again.
i got the normal bootscreen but when x an xfce should start the screen remains black. i cannot say if the x or xfce didn´ start or if it is a problem with the backlight intensity.
rebooting with pandora key and power key leads to the same situation. the only thing that seems to help is to remove the battery shortly.
so, what is the difference beetween reboot after powerdown and reboot after replacing the battery? there could be the point to fix this problem. |
|
180 | Core | Bug Report | Medium | LCD Brightness Lower = Flashing, Dies. | Closed | |
Task Description
Just try and lower with the Fn+Br- until it starts to flashing and just dies if you go lower. It does go back if you raise it again. Feels wrong. Also no real feel in the brightness getting lower. |
|
181 | Application | Bug Report | Low | Triple click in Thunar crash | Closed | |
Task Description
Triple tapping (with the stylus) a directory in Thunar in icon or compact mode (not detail view) causes Thunar to close (crash)
This is consistently repeatable: tapping three times in rapid succession on the same spot of the file causes the crash. It must be the exact same spot, as if double clicking, but a third tap is added. This can be triggered especially when a user becomes frustrated at mistapping, gets carried away, and taps too much. |
|
182 | Core | Bug Report | Medium | Ctrl + F5 (Fn Lock) Fail | Closed | |
Task Description
So I've tried this a while now with no success. I'm assuming its when Fn is triggered and then pressing Ctrl or Alt it goes away. |
|
183 | Core | Bug Report | High | Left mouse click and hold = fail | Closed | |
Task Description
When I want to hold and select multiple files its not working. Not with the nubs or the touchscreen.
I can try an easy test by making the select rectangle on the desktop. It only becomes very very tiny. If I try very fast diagonal drag motion on the touchscreen. It becomes a little larger.
Trying to grab scrollbar is the same issue. |
|
186 | Application | Bug Report | Medium | unusable "Manage LCD Gamma" tool | Closed | |
Task Description
Pandora Menu -> Settings -> LCD-Settings -> Manage LCD Gamma
Removing all the profiles listed there will make the user unable to even create a new one. The tool becomes unusable. I hope a re-flash would fix the problem.
The last profile in the list, or the Default one, shouldn't be deletable at all. |
|
187 | Core | Bug Report | High | LCD turns off after "rdate" updated the date | Closed | |
Task Description
running "sudo rdate -s time.ien.it" will set the brightness of the LCD to 0.
User has to use FN + I to increase it back to a usable level.
"rdate" asks for the super-user password as expected, updates the date as expected, but turns off the screen. |
|
188 | Core | Bug Report | High | "rdate" sets the time exactly 3 hours in advance | Closed | |
Task Description
"rdate -s time.ien.it" will set the date (hour) 3 hours in advance.
The time (and timezone) can be adjusted manually using the "Settings -> Date and Time" tool, but on the next rdate-update the issue will occur again |
|
189 | Core | Bug Report | Medium | pnd-run.sh does not work correctly for very long <pathn ... | Closed | |
Task Description
When unmounting, the pnd-run-script greps the output of "losetup -a" at some point. But if you have a very long pathname and filename for the pnd (like "/media/trans8/gamedata/scummvm/Secret_of_Monkey_Islands_Amiga_EN.pnd" then the endpart is cut off in the output, grep can't find the right part and the script get's confused.
Example:
mounting works:
/usr/pandora/scripts/pnd_run.sh -p /media/trans8/gamedata/scummvm/Secret_of_Monkey_Islands_Amiga_EN.pnd -b scummvm -m
unounting does not work:
/usr/pandora/scripts/pnd_run.sh -p /media/trans8/gamedata/scummvm/Secret_of_Monkey_Islands_Amiga_EN.pnd -b scummvm -u
(see /tmp/pndrun*-logs for output)
The problem is that the outut of losetup looks like this in such a case:
"/dev/loop7: [b309]:157081 (/media/trans8/gamedata/scummvm/Secret_of_Monkey_Islands_Amiga_*)"
And because the pnd-name is not fully shown, grepping the name does not work. After i renamed th pnd to a much shorter name (somi_amiga_en.pnd) it worked nicely. Still this should be fixed. |
|
192 | Core | Bug Report | Medium | [U-Boot] ext2fs_devread() read error - block (boot from ... | Closed | |
Task Description
[U-Boot] ext2fs_devread() read error - block
Description:
Formatted two different Transcend 8GB SD cards as EXT2 using both GParted and also with Mkfs.ext2, extracted pandora-rootfs.tar.bz2 to the root of the SD and added 'autoboot.txt' as described here: http://openpandora.org/firmware/README.txt
This issue appears to be same as mentioned here, looks like a patch maybe required in drivers/mmc/omap3_mmc.c):
http://lists.denx.de/pipermail/u-boot/2010-June/072198.html
Output on boot :
mmc1 is available
reading autoboot.txt
** Unable to read "autoboot.txt" from mc1 0:1 **
Loading file "autoboot.txt" from mmc1 device 0:! (xxa1)
184 bytes read
** Executing plain script at 82000000
Loading file "/boot/uImage-2.6.27.46-omap1" from mmc device 0:1 (xxa1)
** ext2fs_devread() read error - block
** Unable to read "/boot/uImage-2.6.27.46-omap1" from mmc 0:1 **
## Booting kernel from Legacy Image at 8030000 ...
Image Name: Angstrom/2.6.27-pandora+r21+git4
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2325740 Bytes = 2.2 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... Bad Data CRC
ERROR: can't get kernel image!
syntax error |
|
193 | Core | Bug Report | Low | Cannot reach button well in ubuntu x64 | Closed | |
Task Description
Window can also not be resized |
|
194 | Core | Bug Report | Low | python ctypes broken (and fix) | Closed | |
Task Description
run python and type import ctypes
cant find _ctypes it says....
for further details and a fix see
http://www.gp32x.com/board/index.php?/topic/57102-python-ctypes-stopped-working/ |
|
197 | Core | Bug Report | High | [PATCH] Fix opp if booting with wrong settings in hw | Closed | |
Task Description
Hi,
This should help with cases like this
http://www.gp32x.com/board/index.php?/topic/57303-overclocking-broke-my-pandora/
Patch attached. |
|
198 | Application | Bug Report | Low | Mousepad: 'Find' works only once | Closed | |
Task Description
Mousepad 0.2.16
Find (Ctrl+F) works once, the next time it is used the button 'Find' is and stays grayed out. |
|
200 | Core | Bug Report | Low | After opening the lid, the backlight is not reset to th ... | Closed | |
Task Description
Using the hotkeys to set the backlite, after closing and then opening the lid, the backlight is not reset to the same level it was before closing it.
It seems to set it to a fixed value. |
|
202 | Core | Bug Report | Low | Set Date and Time won't let you cancel or close | Closed | |
Task Description
The Date and Time application in MiniMenu by won't let you use the cross or the cancel button to close the application without changing anything.
If you use one of those buttons then a new window opens that says: "Error: Please select a timezone" and equally so for the date and time. |
|
203 | Core | Bug Report | Low | Video-out setting window does not exit on OK | Closed | |
Task Description
The "video-out" window opens again if you choose OK button. |
|
205 | Core | Bug Report | Medium | libpnd functions and dynamic libs missing | Closed | |
Task Description
tried to compile a simple test application that uses functions from libpnd, namely
pnd_evdev_open(pnd_evdev_e)
pnd_evdev_dpad_state(pnd_evdev_e)
pnd_evdev_closeall()
but all 3 seem to be missing.
yes, i'm linking to libpnd ... but no chance to get it running.
i'm using ivanovic's latest toolchain, which in turn installs "pandora-libpnd-dev_1.0-r40.5_armv7a.ipk" ...
also, there's only the static library available inside, no dynamic libraries. |
|
207 | Core | Bug Report | Medium | Touchscreen calibration / use of nubs conflict | Closed | |
Task Description
When using certain apps like Basilisk 2 / Dosbox / Enigma the analogue stick and touchscreen are both available to use as a mouse cursor.
All is well with the touch until you decide to touch the analogue stick when then affects touchscreen alignment by about 2 - 3 CM.
This has been going on since first release. |
|
208 | Core | Bug Report | Critical | HOTFIX 4 and 5 Slow WIFI | Closed | |
Task Description
I'm getting 5kb/s with bursts up to 10kb/s if I am lucky.
I have attempted every channel on my router.
Tried every encryption even no encryption.
Tested with the router's wifi speed: 300Mbps 154Mbps and 45Mbps
I'm running Hotfix 5 RC2.
Wifi works fine with my android smartphone, and other wireless devices such as a laptop. |
|
211 | Core | Bug Report | Low | x11vnc server (in xfce menu - > network) does not work! | Closed | |
Task Description
x11vnc launcher in xfce menu -> network does not work.
can this be fixed please. |
|
213 | Application | Bug Report | Low | Gigolo does not perform it's task | Closed | |
Task Description
In it's current state, Gigolo is flat out broken and (almost) useless. It pretends to to it's job, but can't because it's missing critical pieces of anatomy.
It can mount local filesystems correctly, but then so can thunar, so this is a redundant and useless function. The main reason to use Gigolo is to mount remote filesystems easily, and without having to use the terminal, and to save passwords in your keychain.
The solution to the problem is to perform the following tasks:
sudo opkg install gvfsd-sftp sshfs-fuse
sudo mousepad /etc/modutils/fuse
type "fuse" save and quit
sudo update-modules |
|
214 | Core | Bug Report | High | op_wifi pnd not exiting cleanly, with fix (one characte ... | Closed | |
Task Description
The op_wifi pnd does not exit out cleanly once the encased script executes,
the pndrun_op_wifi.out reports
umount: /mnt/utmp/op_wifi: device is busy.
umount: /mnt/utmp/op_wifi: device is busy.
umount UNION failed, didn't clean up. Process still using this FS :
3197 ? S 0:00 /bin/sh /etc/init.d/wl1251-init start
This op_wifi.sh just calls
/usr/pandora/scripts/op_wifi.sh
for some reason, the init.d/w.... start causes it to hang, I executed all this locally, and it doesn't appear to keep running
Appending " &" to the line which calls this init script, solves the problem. |
|
215 | Core | Bug Report | Medium | Kingston 32GB Class6G2 SDHC card not working in pandora | Closed | |
Task Description
I have noticed errors like this, but not every time
[ 1455.612792] mmc2: card claims to support voltages below the defined range. These will be ignored.
[ 1455.621795] mmc2: SDIO card claims to support the incompletely defined 'low voltage range'. This will be ignored.
[ 1455.665985] mmc2: new SDIO card at address 0001
This is me plugging in my 32GB SD6G2 Kingston SDHC card.
at [ 1114.484252] is when the file copy started
Errors continue from there until it bombs and remounts the filesystem readonly.
I have tried this with ext3 vfat in various configurations and all fail the same I/O errors
Let me know if I can do anything to help
-------------------------------------
[ 989.496459] mmc1: host does not support reading read-only switch. assuming write-enable.
[ 989.504638] mmc1: new high speed SDHC card at address 0003
[ 989.510620] mmcblk1: mmc1:0003 SD32G 31514112KiB
[ 989.515625] mmcblk1: p1 p2 p3 p4 < p5 p6 >
[ 989.940490] FAT: invalid media value (0x00)
[ 989.944702] VFS: Can't find a valid FAT filesystem on dev mmcblk1.
[ 990.083190] FAT: invalid media value (0x00)
[ 990.087402] VFS: Can't find a valid FAT filesystem on dev mmcblk1.
[ 991.907562] EXT3-fs: Unrecognized mount option "umask=0" or missing value
[ 991.922943] EXT3-fs: Unrecognized mount option "umask=0" or missing value
[ 992.002563] mmci-omap mmci-omap.0: MMC IRQ 0x208002 : TC ERRI DCRC
[ 992.003143] mmcblk0: retrying using single block read
[ 992.028411] kjournald starting. Commit interval 5 seconds
[ 992.048553] EXT3-fs: Unrecognized mount option "umask=0" or missing value
[ 992.092346] kjournald starting. Commit interval 5 seconds
[ 992.237091] kjournald starting. Commit interval 5 seconds
[ 992.259185] EXT3-fs: Unrecognized mount option "umask=0" or missing value
[ 992.361999] FAT: bogus number of reserved sectors
[ 992.366760] VFS: Can't find a valid FAT filesystem on dev mmcblk1p4.
[ 992.400909] kjournald starting. Commit interval 5 seconds
[ 992.612945] EXT3 FS on mmcblk1p2, internal journal
[ 992.617797] EXT3-fs: mounted filesystem with ordered data mode.
[ 992.787475] EXT3 FS on mmcblk1p3, internal journal
[ 992.792449] EXT3-fs: mounted filesystem with ordered data mode.
[ 993.038940] EXT3 FS on mmcblk1p1, internal journal
[ 993.043884] EXT3-fs: mounted filesystem with ordered data mode.
[ 993.205749] EXT3 FS on mmcblk1p5, internal journal
[ 993.210632] EXT3-fs: mounted filesystem with ordered data mode.
[ 993.510253] FAT: bogus number of reserved sectors
[ 993.515045] VFS: Can't find a valid FAT filesystem on dev mmcblk1p4.
[ 1114.484252] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1114.484802] mmcblk0: retrying using single block read
[ 1115.763946] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1115.765594] mmcblk0: retrying using single block read
[ 1115.984649] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1115.984985] mmcblk0: retrying using single block read
[ 1116.039489] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.039916] mmcblk0: retrying using single block read
[ 1116.094329] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.094757] mmcblk0: retrying using single block read
[ 1116.150146] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.152343] mmcblk0: retrying using single block read
[ 1116.212127] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.212615] mmcblk0: retrying using single block read
[ 1116.267791] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.268280] mmcblk0: retrying using single block read
[ 1116.335723] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.337738] mmcblk0: retrying using single block read
[ 1116.410766] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.413360] mmcblk0: retrying using single block read
[ 1116.488250] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.490234] mmcblk0: retrying using single block read
[ 1116.581390] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.581939] mmcblk0: retrying using single block read
[ 1116.645721] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.646331] mmcblk0: retrying using single block read
[ 1116.933288] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.933715] mmcblk0: retrying using single block read
[ 1117.000518] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.002899] mmcblk0: retrying using single block read
[ 1117.068328] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.070526] mmcblk0: retrying using single block read
[ 1117.128326] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.128753] mmcblk0: retrying using single block read
[ 1117.194183] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.194488] mmcblk0: retrying using single block read
[ 1117.261566] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.262084] mmcblk0: retrying using single block read
[ 1117.328674] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.329956] mmcblk0: retrying using single block read
[ 1117.388061] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.390380] mmcblk0: retrying using single block read
[ 1117.451629] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.452087] mmcblk0: retrying using single block read
[ 1117.510467] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.512725] mmcblk0: retrying using single block read
[ 1117.714874] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.715301] mmcblk0: retrying using single block read
[ 1117.776550] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.778930] mmcblk0: retrying using single block read
[ 1117.841247] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.841674] mmcblk0: retrying using single block read
[ 1122.718658] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1122.719055] mmcblk0: retrying using single block read
[ 1123.265136] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1123.265441] mmcblk0: retrying using single block read
[ 1123.442230] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1123.442413] mmcblk0: retrying using single block read
[ 1126.759338] mmci-omap mmci-omap.1: MMC IRQ 0x108000 : ERRI DTO
[ 1126.759399] mmcblk1: error -110 transferring data, sector 32669824, nr 8, card status 0xc00
[ 1126.807830] mmci-omap mmci-omap.1: MMC IRQ 0x108000 : ERRI DTO
[ 1126.807891] end_request: I/O error, dev mmcblk1, sector 32669824
[ 1126.813934] Buffer I/O error on device mmcblk1p1, logical block 4083726
[ 1126.820556] lost page write due to I/O error on mmcblk1p1
[ 1127.630950] mmci-omap mmci-omap.1: MMC IRQ 0x108000 : ERRI DTO
[ 1127.631011] mmcblk1: error -110 transferring data, sector 32686232, nr 8, card status 0xc00
[ 1127.715179] mmci-omap mmci-omap.1: MMC IRQ 0x108000 : ERRI DTO
[ 1127.715240] end_request: I/O error, dev mmcblk1, sector 32686232
[ 1127.721282] Buffer I/O error on device mmcblk1p1, logical block 4085777
[ 1127.727935] lost page write due to I/O error on mmcblk1p1
[ 1133.399963] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1133.400024] Spurious DMA IRQ
[ 1133.403411] mmcblk0: retrying using single block read
[ 1133.504821] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1133.504943] mmcblk0: retrying using single block read
[ 1133.599304] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1133.599548] mmcblk0: retrying using single block read
[ 1133.767486] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1133.767578] mmcblk0: retrying using single block read
[ 1134.222564] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1137.074981] mmcblk0: retrying using single block read
[ 1137.465576] mmci-omap mmci-omap.1: MMC IRQ 0x108000 : ERRI DTO
[ 1137.465667] mmcblk1: error -110 transferring data, sector 17316672, nr 72, card status 0xc00
[ 1137.509582] mmci-omap mmci-omap.1: MMC IRQ 0x108000 : ERRI DTO
[ 1137.509643] end_request: I/O error, dev mmcblk1, sector 17316672
[ 1137.515686] end_request: I/O error, dev mmcblk1, sector 17316680
[ 1137.521728] end_request: I/O error, dev mmcblk1, sector 17316688
[ 1137.527770] end_request: I/O error, dev mmcblk1, sector 17316696
[ 1137.533813] end_request: I/O error, dev mmcblk1, sector 17316704
[ 1137.539855] end_request: I/O error, dev mmcblk1, sector 17316712
[ 1137.545867] end_request: I/O error, dev mmcblk1, sector 17316720
[ 1137.551910] end_request: I/O error, dev mmcblk1, sector 17316728
[ 1137.557952] end_request: I/O error, dev mmcblk1, sector 17316736
[ 1137.766906] Aborting journal on device mmcblk1p1.
[ 1137.997436] journal commit I/O error
[ 1138.001037] EXT3-fs error (device mmcblk1p1) in ext3_create: IO failure
[ 1138.225067] ext3_abort called.
[ 1138.228149] EXT3-fs error (device mmcblk1p1): ext3_journal_start_sb: Detected aborted journal
[ 1138.236785] Remounting filesystem read-only |
|
221 | Core | Bug Report | Medium | 32MB worth of qt4 examples in /usr/bin/qt4 ? | Closed | |
Task Description
Hi, after upgrading to HF5, I accidentally discovered that there are 32MB of qt4 examples & demos in directory /usr/bin/qt4, those examples do work. For instance the /usr/bin/qt4/examples/webkit/fancybrowser/fancybrowser is a working WWW browser.
It is, without any dispute a very useful qt4 development help, but are you sure that you want to include all that in NAND ? |
|
224 | Core | Bug Report | Low | Unresponsive start menu since HF5 | Closed | |
Task Description
Since hotfix 5, the start menu often pauses for a few seconds, not letting me select anything or move the mouse.
Other people have reported the issue as well:
http://boards.openpandora.org/index.php?/topic/2295-is-the-xfce-menu-trolling-anyone-else/page__gopid__42559#entry42559 |
|
228 | Core | Bug Report | Low | libpnd must be linked to libstdc++ | Closed | |
Task Description
Run "ldd -r /usr/lib/libpnd.so.1", and a number of undefined symbols are listed. These become a problem when attempting to load libpnd in Python. I imagine it could be a problem when attempting to load libpnd in other languages as well.
This can be worked around with "LD_PRELOAD=/usr/lib/libstdc++.so" before running a Python program that loads libpnd.
But it can be worked around more easily by linking libstdc++ during compile. Adding "-lstdc++" to line 41 of libpnd's Makefile does it. I'd add a patch, but the attach file button isn't working for me. Still, a simple fix, right? |
|
230 | Core | Bug Report | Low | Second SD slot not working in future kernel version 2.6 ... | Closed | |
Task Description
Sorry, not sure where to log this bug. I have confirmed with aTc on freenode, that SD slot #2 does not work on kernel version 2.6.37 from the openpandora git.
Happy to test anything and reports results. |
