|
177 | Core | Bug Report | Medium | no x or xfce after shutdown and reboot | Closed | |
Task Description
often but not always after shutting down the system (xfce logout, choose shutdown) there´s a problem when booting again.
i got the normal bootscreen but when x an xfce should start the screen remains black. i cannot say if the x or xfce didn´ start or if it is a problem with the backlight intensity.
rebooting with pandora key and power key leads to the same situation. the only thing that seems to help is to remove the battery shortly.
so, what is the difference beetween reboot after powerdown and reboot after replacing the battery? there could be the point to fix this problem. |
|
30 | Core | Bug Report | Medium | New issues in current image (pandora-20100102-new-kerne ... | Closed | |
Task Description
* It takes forever to startup.
It hangs while trying to initialize the new SDIO-WiFi:
[ 2363.922271] wl1251: WARNING WLAN not ready
[ 2363.927581] wl1251_sdio mmc2:0001:1: firmware: requesting wl1251-fw.bin
[ 2423.930328] wl1251: ERROR could not get firmware: -2
[ 2424.033447] wl1251: ERROR sdio write failed (-110)
[ 2425.786071] wl1251: ERROR sdio read failed (-110)
[ 2425.790893] wl1251: WARNING WLAN not ready
[ 2425.795776] wl1251_sdio mmc2:0001:1: firmware: requesting wl1251-fw.bin
* OpenPandora Start-Button is too small (has the same width as a normal icon) |
|
56 | Core | Bug Report | Medium | Movie Playing (Totem, VLC and MPlayer) | Closed | |
Task Description
Not really a bug report, just an information what issues what player has (tested using image from Feb 22nd).
MPlayer is missing a library in this image:
libxxf86dga1
Installing that one manually does make it work.
* VLC:
Plays things, but switching to fullscreen and back causes VLC to start having issues.
I wouldn't recomment VLC.
* Totem:
Works well (fullspeed video playing) when you disable the sidebar.
With the sidebar enabled, it doesn't play videos in fullscreen.
Menus are behind the video overlay as well as the controls in fullscreen mode (which is a bummer).
Needs about 10% more for the same movie than MPlayer (and therefore, stutters more often when mmcqd eats up CPU power)
* MPlayer:
Works well (fullspeed video playing) when video out is set to XV.
Audio out needs to be set to OSS. If set to Alsa, it segfaults when scrubbing around or doing a fast forward (see segfault below).
Runs very well in fullscreen, including controls on the bottom.
Does have issues displaying videos in windows (usually shows black, unless you resize the window).
Cache should be set to 40000. This will almost remove the stuttering when mmcqd accesses the SD card.
Menu is behind the video stream as well.
Only bad thing about Gnome MPlayer is, that you can't run it in fullscreen automatically when a video is loaded.
So basically, MPlayer is the best we have at the moment.
Fullscreen is really working flawlessly. Maybe we could change Gnome MPlayer to some fullscreen GUI (like the MPlayer for the Wii, etc.).
For a first release, it already works well enough.
Just need to make sure we include default settings as described above (most important: OSS sound!)
In case anyone wants to debug, here is the segfault that happens when using ALSA and fast forwarding:
[ 976.602203] Unable to handle kernel paging request at virtual address ffc84000
[ 976.609466] pgd = cf770000
[ 976.612182] [ffc84000] *pgd=8f842011, *pte=00000000, *ppte=00000000
[ 976.618530] Internal error: Oops: 807 [#1]
[ 976.622650] Modules linked in: g_cdc pvrsrvkm ipv6 ads7846 hwmon
[ 976.628723] CPU: 0 Not tainted (2.6.27-omap1 #1)
[ 976.633758] PC is at memset+0x30/0xc0
[ 976.637420] LR is at 0x0
[ 976.639984] pc : [] lr : [] psr: 20000093
[ 976.639984] sp : cf5abe04 ip : 00000000 fp : cf5abe24
[ 976.651519] r10: ffffe0a4 r9 : 00001d4c r8 : 00004c3b
[ 976.656799] r7 : ffffe0a4 r6 : cf8975c0 r5 : ffffc148 r4 : cfaed400
[ 976.663360] r3 : 00000000 r2 : 1ff8b350 r1 : 00000000 r0 : ffc83ffc
[ 976.669921] Flags: nzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
[ 976.677185] Control: 00c5387f Table: 8f770018 DAC: 00000015
[ 976.682952] Process mplayer (pid: 1781, stack limit = 0xcf5aa2e8)
[ 976.689086] Stack: (0xcf5abe04 to 0xcf5ac000)
[ 976.693481] be00: c02b4e00 cfae0a00 cfaed400 00005007 cf8975c0 cf5abe5c cf5abe28
[ 976.701873] be20: c02b2f74 c02b4da4 cf8975c0 cf5abe38 c0066db0 cfaed400 00005007 cf8975c0
[ 976.710235] be40: 00004c3b cf8975c0 00001d4c 00000000 cf5abe7c cf5abe60 c02b36f8 c02b2d94
[ 976.718627] be60: 00001d4c cfaed400 cf8975c0 00000000 cf5abecc cf5abe80 c02b3b50 c02b362c
[ 976.726989] be80: c00699fc c00382ac cf5abeb0 00000000 00ecdda0 00000000 cf5abee4 cf5abea8
[ 976.735382] bea0: c006a104 00001d4c 400c4150 cf8975c0 bef6050c c002ee44 cf5aa000 00000000
[ 976.743774] bec0: cf5abeec cf5abed0 c02b3dbc c02b3ac8 c02b31c4 bef6050c c002ee44 00000000
[ 976.752136] bee0: cf5abf1c cf5abef0 c02b1188 c02b3d64 c04ae8a0 00000000 00ecdda0 00001d4c
[ 976.760528] bf00: bef6050c 400c4150 bef6050c cf778760 cf5abf34 cf5abf20 c02b1504 c02b10d4
[ 976.768890] bf20: cf5abf5c cf778760 cf5abf54 cf5abf38 c00aa8ac c02b14d0 bef60548 cf778760
[ 976.777282] bf40: bef6050c 00000007 cf5abf7c cf5abf58 c00aab4c c00aa880 c0066e74 bef60548
[ 976.785675] bf60: cf5abf80 00000007 bef6050c 400c4150 cf5abfa4 cf5abf80 c00aaba4 c00aa8fc
[ 976.794036] bf80: 4b82cf18 00000000 00da2268 00da22b8 00000000 00000036 00000000 cf5abfa8
[ 976.802429] bfa0: c002ecc0 c00aab70 00da2268 00da22b8 00000007 400c4150 bef6050c bef6050c
[ 976.810821] bfc0: 00da2268 00da22b8 00000000 00000036 00d40628 00000000 00000000 00871348
[ 976.819183] bfe0: 00887178 bef60508 4012354c 4071963c 60000010 00000007 b601206b df08c3ff
[ 976.827575] Backtrace:
[ 976.830047] [] (snd_pcm_format_set_silence+0x0/0x13c) from [] (snd_pcm_playback_silence+0x1ec/0x2ac)
[ 976.841033] r6:cf8975c0 r5:00005007 r4:cfaed400
[ 976.845703] [] (snd_pcm_playback_silence+0x0/0x2ac) from [] (snd_pcm_update_hw_ptr+0xd8/0x1b4)
[ 976.856140] [] (snd_pcm_update_hw_ptr+0x0/0x1b4) from [] (snd_pcm_lib_write1+0x94/0x23c)
[ 976.866058] r7:00000000 r6:cf8975c0 r5:cfaed400 r4:00001d4c
[ 976.871765] [] (snd_pcm_lib_write1+0x0/0x23c) from [] (snd_pcm_lib_write+0x64/0x70)
[ 976.881256] [] (snd_pcm_lib_write+0x0/0x70) from [] (snd_pcm_playback_ioctl1+0xc0/0x3fc)
[ 976.891174] r4:00000000
[ 976.893737] [] (snd_pcm_playback_ioctl1+0x0/0x3fc) from [] (snd_pcm_playback_ioctl+0x40/0x44)
[ 976.904083] r7:cf778760 r6:bef6050c r5:400c4150 r4:bef6050c
[ 976.909820] [] (snd_pcm_playback_ioctl+0x0/0x44) from [] (vfs_ioctl+0x38/0x7c)
[ 976.918853] r4:cf778760
[ 976.921417] [] (vfs_ioctl+0x0/0x7c) from [] (do_vfs_ioctl+0x25c/0x274)
[ 976.929748] r6:00000007 r5:bef6050c r4:cf778760
[ 976.934417] [] (do_vfs_ioctl+0x0/0x274) from [] (sys_ioctl+0x40/0x64)
[ 976.942657] r6:400c4150 r5:bef6050c r4:00000007
[ 976.947326] [] (sys_ioctl+0x0/0x64) from [] (ret_fast_syscall+0x0/0x2c)
[ 976.955749] r7:00000036 r6:00000000 r5:00da22b8 r4:00da2268
[ 976.961486] Code: e1a0c001 e1a0e001 e2522040 a8a0500a (a8a0500a)
[ 976.967773] ---[ end trace 83bdb29850a1e142 ]--- |
|
310 | Core | Bug Report | Medium | mkdosfs is broken - creates 1GiB filesystems | Closed | |
Task Description
When a partition is bigger than 2 or 4 GiB (can't recall now) it makes a "default" 1GiB filesystem. Propably missing large file support in the build. Also, the pandora sd card formatter is missing -F 32 so it makes (i think, it is some time from when I noticed this) FAT16 partitions... |
|
301 | Core | Bug Report | Medium | Missing X keybinding for colon symbol | Unconfirmed | |
Task Description
As verified with xev, an attached bluetooth keyboard can not generate colon (shift semicolon). xmodmap shows that (unlike a standard Linux system) shift-semicolon is mapped to NoSymbol. While it's find that there's a special symbol to get semicolon on the built-in keyboard, the other binding really should be there in support of attached keyboards. |
|
243 | Application | Feature Request | Medium | MiniMenu: Pressing successive character keys should com... | Unconfirmed | |
Task Description
Imagine this tab content:
Nubs, Pandora Input, PNDstore.
CURRENT BEHAVIOR:
Pressing "P" and "N" is succession jumps to "Nubs" eventually, as it first jumps to the first "P" item ("Pandora Input"), then to the first "N" item, "Nubs".
DESIRED BEHAVIOR:
That it acts like in most Linux file browsers or the Mac OS X Finder.
In detail: Pressing "P" and "N" within a certain time limit should combine them to the string "PN" and jump to the first item which starts with that string, i.e. "PNDStore". If no item matches, reduce the combination string by one character, try to match again, if that doesn't match, try matching again with one character less, ... , until only one character is left, and if that one doesn't match jump to the nearest previous lexicographical character, which matches. |
|
265 | Application | Bug Report | Medium | MiniMenu: Flawed tab display of sub-categories if they ... | Unconfirmed | |
Task Description
I assigned personal subcategories to some of my games.
Some of those subcategories share the same beginning string, i.e: Shooter, ShooterBallistic ShooterScoller.
MiniMenu displays those subcategories with flaws! See the ASCII screenshots below.
Note: The star symbols indicate the currently active selection.
The main category tab "Game" being active:
----------------------------------------------------------
| All | Audio | AudioVideo | Education |*Game*| Graphics |
----------------------------------------------------------
ActionGame AdventureGame ArcadeGame BlocksGame ...
Shooter ShooterBallistic ShooterScroller ...
GameA GameB GameC ...
----------------------------------------------------------
Now if I navigate into the sub-category "Shooter", everything normal:
----------------------------------------------------------
|*Shooter*|
----------------------------------------------------------
.. ShooterA ShooterB ShooterC ...
----------------------------------------------------------
But if I navigate to the sub-category "ShooterBallistic", strangely MiniMenu shows 2 tabs, "Shooter" and "ShooterBallistic", and jumps right into "Shooter".
----------------------------------------------------------
|*Shooter*| ShooterBallistic |
----------------------------------------------------------
.. ShooterA ShooterB ShooterC ...
----------------------------------------------------------
In order to reach my intended tab "ShooterBallistic" I need to navigate to it again. Annoying. There the contents are as expected:
----------------------------------------------------------
| Shooter |*ShooterBallistic*|
----------------------------------------------------------
.. ShooterBallisticA ShooterBallisticB ShooterBallisticC
----------------------------------------------------------
The flaw is the same for all other sub-categories beginning with "Shooter...". All have the flaw as shown in the example "ShooterBallistic", only that it is themselves instead of "ShooterBallistic". One more example to be perfectly clear:
----------------------------------------------------------
| Shooter |*ShooterScroller*|
----------------------------------------------------------
.. ShooterScrollerA ShooterScrollerB ShooterScrollerC
---------------------------------------------------------- |
|
262 | Application | Bug Report | Medium | MiniMenu: 1) "Notes line" cannot be deleted. 2) Note li... | Unconfirmed | |
Task Description
Steps to reproduce the bug(s):
1) In MiniMenu select an arbitrary app.
2) Press SPACE to bring up the contextual menu.
3) Select "Edit notes line 1".
4) Insert your string and confirm.
5) Now at a later time you may decide to remove your note line again. Therefore you select the same app again in MiniMenu, then repeat steps 2-3, but this time:
a) Erase all characters so that you get an empty string and then confirm. RESULT: Your change is simply ignored! There should be a possibility within MiniMenu to remove/reset note lines, the simplest being to simply accept an empty string as an input, that's what an average user will try if s/he does not find a dedicated "Delete note line" command.
b) As a workaround I tried something and detected yet another bug! As I could not create an empty string, I simply created a note line only containing 1 SPACE character (=the string " ") and confirmed. This got accepted.
If MiniMenu is in detailed view mode (press the A-button or TAB in order to bring it up, if it is not already there) and you slide over an app whose note line is " ", MiniMenu crashes!
Maybe the bug is connected with the writing to / the parsing from the .OVR (override) files which MiniMenu creates for the affected files, as the separating value in OVR files seems to be TAB, and SPACE is also WHITESPACE, therefore some parsers probably skip/misinterpret this, and MiniMenu then catches an unexpected situation!
WORKAROUND: If you ran into the problem, that you cannot get rid of the note lines anymore, simply start a file browser of your choice, navigate to the location of the affected .PND file and find its sister .OVR (override) file and delete it or edit it accordingly! |
|
111 | Core | Feature Request | Medium | Minimal Boot to X_Term / Pico | Closed | |
Task Description
Can we add an option to the boot menu for a minimal boot to X-term, and include Pico in the base OS?
This would allow us to fix problems we've caused by messing around with starup scripts etc.. |
|
260 | Core | Bug Report | Medium | Low Power Mode: Input (keyboard, nub) still taken. Appl... | Unconfirmed | |
Task Description
This is the related documentation:
http://pandorawiki.org/Power_modes#Low_Power
(Please update accordingly as part of the issue resolution)
FROM MY USER EXPERIENCE:
If you put the Pandora into Low Power Mode, then press some keys, and then wake the Pandora back into Normal Mode, your input (both keys and nubs, haven't tried with USB input yet) seem to have triggered something while the device was in Low Power Mode!
What does really happen in Low Power Mode concerning execution and input?
a) Input is received AND triggers as application execution continues
or
b) Kernel/driver queues the input signals into a buffer, and executes them on wake?
If supposition a) or b) is true, then this would be one more reason to properly implement: FS#259
OBSERVANCE EXAMPLE 1:
1) Start MiniMenu. Mentally note down your active tab.
2) Put Pandora to Low Power Mode.
3) Press shoulder button R once.
4) Wake Pandora to Normal Mode. You are now one tab to the right of where you left. Input must have been caught in Low Power Mode, but wether execution of it happened while Low Power Mode or later after wake in Normal power Mode is unclear.
OBSERVANCE EXAMPLE 2:
1) Start gedit (a text editor). Insert the digit "1".
2) Put Pandora to Low Power Mode.
3) Press: CTRL-N 2 CTRL-N 3 CTRL-N 4. (Without the spaces)
4) Wake Pandora to Normal Mode.
5) For a fraction of a second you see the tabs building up. Either the input was really received AND executed while Low Power Mode and what you see is just a delayed window manager refreshment, or the input was queued in Low Power Mode, and only executed on wake. |
|
43 | Core | Bug Report | Medium | libpng missing from the last images (since approx mid o ... | Closed | |
Task Description
Some ports (like SMW, VICE, etc.) stopped working because libpng is missing from the current images.
Installing it does fix that problem.
http://www.angstrom-distribution.org/unstable/feed/armv7a/base/libpng_1.2.42-r2.0.5_armv7a.ipk |
|
45 | Core | Bug Report | Medium | libpnd: Using German descriptions from PND files | Closed | |
Task Description
I have some PNDs which have a german description included. pmenu does use those instead of the english ones (which should be the default if no language is selected). |
|
184 | Core | Feature Request | Medium | libpnd: Add a function to get all mounted PNDs | Closed | |
Task Description
Add a function to get all mounted PNDs. Because it's very annoying to check all the menu/desktop folders on all of the SD-Cards. |
|
205 | Core | Bug Report | Medium | libpnd functions and dynamic libs missing | Closed | |
Task Description
tried to compile a simple test application that uses functions from libpnd, namely
pnd_evdev_open(pnd_evdev_e)
pnd_evdev_dpad_state(pnd_evdev_e)
pnd_evdev_closeall()
but all 3 seem to be missing.
yes, i'm linking to libpnd ... but no chance to get it running.
i'm using ivanovic's latest toolchain, which in turn installs "pandora-libpnd-dev_1.0-r40.5_armv7a.ipk" ...
also, there's only the static library available inside, no dynamic libraries. |
|
91 | Base OS | Bug Report | Medium | libaudiofile is installed by codec pack instead of in b ... | Closed | |
Task Description
Certain emulators such as Fuse are reliant on this file and I am assured it should be part of the default load-out (or rather in the HotFix) rather than in the codec pack as it's not a copyright issue. |
|
180 | Core | Bug Report | Medium | LCD Brightness Lower = Flashing, Dies. | Closed | |
Task Description
Just try and lower with the Fn+Br- until it starts to flashing and just dies if you go lower. It does go back if you raise it again. Feels wrong. Also no real feel in the brightness getting lower. |
|
215 | Core | Bug Report | Medium | Kingston 32GB Class6G2 SDHC card not working in pandora | Closed | |
Task Description
I have noticed errors like this, but not every time
[ 1455.612792] mmc2: card claims to support voltages below the defined range. These will be ignored.
[ 1455.621795] mmc2: SDIO card claims to support the incompletely defined 'low voltage range'. This will be ignored.
[ 1455.665985] mmc2: new SDIO card at address 0001
This is me plugging in my 32GB SD6G2 Kingston SDHC card.
at [ 1114.484252] is when the file copy started
Errors continue from there until it bombs and remounts the filesystem readonly.
I have tried this with ext3 vfat in various configurations and all fail the same I/O errors
Let me know if I can do anything to help
-------------------------------------
[ 989.496459] mmc1: host does not support reading read-only switch. assuming write-enable.
[ 989.504638] mmc1: new high speed SDHC card at address 0003
[ 989.510620] mmcblk1: mmc1:0003 SD32G 31514112KiB
[ 989.515625] mmcblk1: p1 p2 p3 p4 < p5 p6 >
[ 989.940490] FAT: invalid media value (0x00)
[ 989.944702] VFS: Can't find a valid FAT filesystem on dev mmcblk1.
[ 990.083190] FAT: invalid media value (0x00)
[ 990.087402] VFS: Can't find a valid FAT filesystem on dev mmcblk1.
[ 991.907562] EXT3-fs: Unrecognized mount option "umask=0" or missing value
[ 991.922943] EXT3-fs: Unrecognized mount option "umask=0" or missing value
[ 992.002563] mmci-omap mmci-omap.0: MMC IRQ 0x208002 : TC ERRI DCRC
[ 992.003143] mmcblk0: retrying using single block read
[ 992.028411] kjournald starting. Commit interval 5 seconds
[ 992.048553] EXT3-fs: Unrecognized mount option "umask=0" or missing value
[ 992.092346] kjournald starting. Commit interval 5 seconds
[ 992.237091] kjournald starting. Commit interval 5 seconds
[ 992.259185] EXT3-fs: Unrecognized mount option "umask=0" or missing value
[ 992.361999] FAT: bogus number of reserved sectors
[ 992.366760] VFS: Can't find a valid FAT filesystem on dev mmcblk1p4.
[ 992.400909] kjournald starting. Commit interval 5 seconds
[ 992.612945] EXT3 FS on mmcblk1p2, internal journal
[ 992.617797] EXT3-fs: mounted filesystem with ordered data mode.
[ 992.787475] EXT3 FS on mmcblk1p3, internal journal
[ 992.792449] EXT3-fs: mounted filesystem with ordered data mode.
[ 993.038940] EXT3 FS on mmcblk1p1, internal journal
[ 993.043884] EXT3-fs: mounted filesystem with ordered data mode.
[ 993.205749] EXT3 FS on mmcblk1p5, internal journal
[ 993.210632] EXT3-fs: mounted filesystem with ordered data mode.
[ 993.510253] FAT: bogus number of reserved sectors
[ 993.515045] VFS: Can't find a valid FAT filesystem on dev mmcblk1p4.
[ 1114.484252] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1114.484802] mmcblk0: retrying using single block read
[ 1115.763946] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1115.765594] mmcblk0: retrying using single block read
[ 1115.984649] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1115.984985] mmcblk0: retrying using single block read
[ 1116.039489] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.039916] mmcblk0: retrying using single block read
[ 1116.094329] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.094757] mmcblk0: retrying using single block read
[ 1116.150146] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.152343] mmcblk0: retrying using single block read
[ 1116.212127] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.212615] mmcblk0: retrying using single block read
[ 1116.267791] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.268280] mmcblk0: retrying using single block read
[ 1116.335723] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.337738] mmcblk0: retrying using single block read
[ 1116.410766] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.413360] mmcblk0: retrying using single block read
[ 1116.488250] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.490234] mmcblk0: retrying using single block read
[ 1116.581390] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.581939] mmcblk0: retrying using single block read
[ 1116.645721] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.646331] mmcblk0: retrying using single block read
[ 1116.933288] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1116.933715] mmcblk0: retrying using single block read
[ 1117.000518] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.002899] mmcblk0: retrying using single block read
[ 1117.068328] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.070526] mmcblk0: retrying using single block read
[ 1117.128326] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.128753] mmcblk0: retrying using single block read
[ 1117.194183] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.194488] mmcblk0: retrying using single block read
[ 1117.261566] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.262084] mmcblk0: retrying using single block read
[ 1117.328674] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.329956] mmcblk0: retrying using single block read
[ 1117.388061] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.390380] mmcblk0: retrying using single block read
[ 1117.451629] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.452087] mmcblk0: retrying using single block read
[ 1117.510467] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.512725] mmcblk0: retrying using single block read
[ 1117.714874] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.715301] mmcblk0: retrying using single block read
[ 1117.776550] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.778930] mmcblk0: retrying using single block read
[ 1117.841247] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1117.841674] mmcblk0: retrying using single block read
[ 1122.718658] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1122.719055] mmcblk0: retrying using single block read
[ 1123.265136] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1123.265441] mmcblk0: retrying using single block read
[ 1123.442230] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1123.442413] mmcblk0: retrying using single block read
[ 1126.759338] mmci-omap mmci-omap.1: MMC IRQ 0x108000 : ERRI DTO
[ 1126.759399] mmcblk1: error -110 transferring data, sector 32669824, nr 8, card status 0xc00
[ 1126.807830] mmci-omap mmci-omap.1: MMC IRQ 0x108000 : ERRI DTO
[ 1126.807891] end_request: I/O error, dev mmcblk1, sector 32669824
[ 1126.813934] Buffer I/O error on device mmcblk1p1, logical block 4083726
[ 1126.820556] lost page write due to I/O error on mmcblk1p1
[ 1127.630950] mmci-omap mmci-omap.1: MMC IRQ 0x108000 : ERRI DTO
[ 1127.631011] mmcblk1: error -110 transferring data, sector 32686232, nr 8, card status 0xc00
[ 1127.715179] mmci-omap mmci-omap.1: MMC IRQ 0x108000 : ERRI DTO
[ 1127.715240] end_request: I/O error, dev mmcblk1, sector 32686232
[ 1127.721282] Buffer I/O error on device mmcblk1p1, logical block 4085777
[ 1127.727935] lost page write due to I/O error on mmcblk1p1
[ 1133.399963] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1133.400024] Spurious DMA IRQ
[ 1133.403411] mmcblk0: retrying using single block read
[ 1133.504821] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1133.504943] mmcblk0: retrying using single block read
[ 1133.599304] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1133.599548] mmcblk0: retrying using single block read
[ 1133.767486] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1133.767578] mmcblk0: retrying using single block read
[ 1134.222564] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC
[ 1137.074981] mmcblk0: retrying using single block read
[ 1137.465576] mmci-omap mmci-omap.1: MMC IRQ 0x108000 : ERRI DTO
[ 1137.465667] mmcblk1: error -110 transferring data, sector 17316672, nr 72, card status 0xc00
[ 1137.509582] mmci-omap mmci-omap.1: MMC IRQ 0x108000 : ERRI DTO
[ 1137.509643] end_request: I/O error, dev mmcblk1, sector 17316672
[ 1137.515686] end_request: I/O error, dev mmcblk1, sector 17316680
[ 1137.521728] end_request: I/O error, dev mmcblk1, sector 17316688
[ 1137.527770] end_request: I/O error, dev mmcblk1, sector 17316696
[ 1137.533813] end_request: I/O error, dev mmcblk1, sector 17316704
[ 1137.539855] end_request: I/O error, dev mmcblk1, sector 17316712
[ 1137.545867] end_request: I/O error, dev mmcblk1, sector 17316720
[ 1137.551910] end_request: I/O error, dev mmcblk1, sector 17316728
[ 1137.557952] end_request: I/O error, dev mmcblk1, sector 17316736
[ 1137.766906] Aborting journal on device mmcblk1p1.
[ 1137.997436] journal commit I/O error
[ 1138.001037] EXT3-fs error (device mmcblk1p1) in ext3_create: IO failure
[ 1138.225067] ext3_abort called.
[ 1138.228149] EXT3-fs error (device mmcblk1p1): ext3_journal_start_sb: Detected aborted journal
[ 1138.236785] Remounting filesystem read-only |
|
331 | Core | Bug Report | Medium | Hold switch key continuously sends X11 KeyPress events ... | Unconfirmed | |
Task Description
When put into Hold mode, X11 handles the power switch as if it's being pressed, and it generates lots of keypress events, passing them to the foreground application. Since /dev/input/eventX does not seem to continuously trigger, I'm guessing it's due to key repeat.
To reproduce:
- Install xev and open it in the terminal
- Put the power key in HOLD mode
- Notice the "time" value changing rapidly
In addition to causing more work to X, it also floods the active application with key presses, resulting in increased CPU usage. In my test, switching to HOLD while Firefox is in the foreground causes it to use 6% CPU and X an additional 2.5%.
In addition, the key-press events continue even after the switch is taken off HOLD until another key is pressed.
A possible solution to this is to blacklist the power-button event device, to prevent evdev from listening to it (the key is handled by pndevmapperd). |
|
290 | Core | Bug Report | Medium | gnome-mount not available | Unconfirmed | |
Task Description
In GTK applications, such as Truecrypt, NoteCase Pro or Mousepad, the file open / file save dialogs have shortcuts to mounted file systems on the left side.
If clicking such a shortcut entry, the corresponding file system's contents are shown in the right dialog pane.
This works for file systems, which were available at boot time.
For file systems mounted after booting, e.g. by inserting an SD card or connecting a USB drive, when clicking such an entry, an error message appears saying
"Could not mount [volumen name]
Failed to execute child process 'gnome-mount' (No such file or directory)"
This is healed by
sudo opkg install gnome-mount
(which instals gnome-mount, nautilus, gvfsd-ftp, gvfs (upgrade), and a lot of libs (upgrades)..
This has been seen in SuperZaxxon release 1.5, not in Beta3 (but Beta3 is the only choice in Flyspray's dropdown currently).
I reported that error for HF6 I think, and it seemed to be fixed in SuperZaxxon Beta5. A regression? |
|
204 | Core | Bug Report | Medium | fonts issues | Unconfirmed | |
Task Description
Ok, I just want to say that there is something missing about the font on the base image. I cant get what (at least for now)
Here is an issue : http://www.gp32x.com/board/index.php?/topic/54282-getting-vnc-viewer-to-work/
With my current Ogre build I get :
Warning: Unable to load any usable ISO8859 font
Error: Aborting: no font found
I've googled but so far no solution :( |
|
250 | Application | Feature Request | Medium | File Browser Thunar - Trashing file crosses filesystem ... | Researching | |
Task Description
Trashing a file/folder seems to MOVE it to a certain trash directory on the MAIN VOLUME, rather then the ORIGINATING VOLUME, hence this can result in a COPY RATHER THAN A MOVE operation, if the trashed file originates from a filesystem other than the main filesystem!
This is very inefficient and faulty as it is:
a) Very time consuming
b) And in case of large files this operation can even fail due to not enough free space on the main volume. |
|
170 | Core | Bug Report | Medium | Executable directories broken | Closed | |
Task Description
Directory type packages fail to run. i.e. dropping a directory containing PXML.xml and a bunch of files onto the SD card rather than a .pnd package.
The application is detected and menu entries created correctly, however pnd_run.sh fails to bind mount the directory due to bogus double quoting. Looks like a failed attempt to handle spaces in the path. Patch below removes these incorrect quotes.
--- pnd_run.sh
+++ pnd_run.sh.old
@@ -161,2 +161,2 @@
elif [ $DFS = directory ]; then
- mntline="sudo mount --bind -o ro ${PND} "
+ mntline="sudo mount --bind -o ro \"${PND}\" " |
|
47 | Core | To Do (Reminder) | Medium | evmapperd: Blinking LED and charging control | Closed | |
Task Description
evmapperd should start blinking when the power is getting low.
Ideally, the blinking speed should increase with decreasing battery power and should start maybe at 5% as default (would be nice to have the settings configurable by the user).
As soon as the AC adaptor is connected, blinking should stop.
When the battery power is at 0% it should immediately shutdown and poweroff (NOT to be overridden by the user!)
Aditionally, we should have some charging control (or would it be better using a different daemon for that?)
Here's part of my conversation with MichaelW:
when the charge current was below a threshold, it would reduce the charger input current allowed and take it down to about what the system needs
it would be an active thing constantly sampling the system and constantly updating the input current to match the system
the alternative is that when the battery is full, the charge path is cut off until the battery drops down a bit, maybe 90% |
|
132 | Base OS | Bug Report | Medium | Deleting big files doesn't work | Closed | |
Task Description
When deleting a file on the SD card, the Pandora OS moves it into the thrash folder in the internal memory. That itself isn't very nice (shouldn't there be a trash folder on the SD card as well, to reduce unnecessary copying?), but if the file is too big for the internal memory, a error message appears, and the file cannot be deleted on the Pandora directly. |
|
87 | Core | Bug Report | Medium | default /etc/network/interfaces is causing problems | Closed | |
Task Description
The default /etc/network/interfaces has 192.168.1.0/24 subnet set up for usb0 which causes wifi connectivity to fail for users that have wifi on the same subnet.
All addresses should be edited out from /etc/network/interfaces, eth* stuff should probably be dropped too. |
|
182 | Core | Bug Report | Medium | Ctrl + F5 (Fn Lock) Fail | Closed | |
Task Description
So I've tried this a while now with no success. I'm assuming its when Fn is triggered and then pressing Ctrl or Alt it goes away. |
|
155 | Core | Bug Report | Medium | Critical problems after rescaling GLES2 X windows | Unconfirmed | |
Task Description
When a X window which is displaying GLES2 render output is:
- Either dragged out of the visibile screen region (?)
- Is made larger than it was at the creation time of the GLES2 context
then:
- The performance will drop significantly as the EGL buffer swaps won't occur as fast as before,
- The render output will be corrupted and flicker
- In rare occasions crashes the application or locks up the entire system (which forces you to remove the battery)
The problem can not be solved without restarting the application (Possibly forcing players to complete the same goals again as they were unable to reach a savepoint or similar things).
This was confirmed in Mupen64Plus and the PowerVR GLES Samples and some of my own projects (which are, however, based on the PowerVR samples).
As I didn't see any other reports about this problems (but had it confirmed by other Pandora users too) I would expect that it can be fixed by using a newer X, kernel or combination of them as other OMAP users would be effected too. |
|
246 | Application | Bug Report | Medium | Clipboard content of closed app gets tossed instead of ... | Unconfirmed | |
Task Description
FLAWED BEHAVIOUR:
Copy and paste only works between 2 active applications. This is very limiting!
If you are in the single task oriented MiniMenu you have no chance at all to share the clipboard between apps!
If you are in the multi tasking oriented XFCE desktop environment you can only share between apps running in parallel! Not with apps which started after the source app has been terminated.
DESIRED BEHAVIOUR:
The clipboard content (within reasonable limits of course) should remain, regardless of the source application, so that you can paste at any later moment into any application. |
|
234 | Core | Feature Request | Medium | Changeable behaviour when closing the lid | Closed | |
Task Description
As it was requested on forum.gp2x.de and I think it's a good idea I've written some scripts to allow the user to change what happens when the lid is opened/closed.
There are 3 Settings:
-The old behaviour (turning off the screen)
-Go into low power mode
-Shutdown
Default behaviour is still the same: Turn the screen off. Maybe we could change this to low power mode? I don't know.
I made a lot of changes to op_lid.sh: http://pastebin.com/GT3qxWSx (diff: http://pastebin.com/Z8GwpDj8 )
I changed line 11 in op_power.sh to: if [ $powerstate -ne 0 ]; then
And wrote a gui for changing the setting using zenity: http://pastebin.com/9JvSTqfQ
(I still can't upload any files, don't know if it's the fault of my browser, that's why I use this paste service) |
|
307 | Core | Feature Request | Medium | Change how Automatic Shutdown works | Unconfirmed | |
Task Description
When thee Pandora is shutting down because its almost out of power, it should check to make sure that the nub inputs are set to the default mode (which is mouse movement for the left nub and mouse buttons for the right nub). If not, it should change them to be like that. |
|
95 | Base OS | Bug Report | Medium | Cannot Connect to Ad-Hoc WIFI | Closed | |
Task Description
I am Currently tethering my Mobile Network via my Android Phone
I cannot connect on this WIFI ... it's a Ad-Hoc connection
Everything else works, PC, Netbook's and iPod Touch
But Pandora seems to have some problems |
|
6 | Core | Bug Report | Medium | Calibrate Touchscreen within the Settings-Menu of XFCE ... | Closed | |
Task Description
It doesn't run. |
|
131 | Core | Bug Report | Medium | bluetooth drivers read timeout too trigger-happy/logic ... | Closed | |
Task Description
Shamelessly plugged from the forums, to get proper bug tracking and notifications on this. My post:
@notaz:
+ /* there hould be no rx in progress at this point */
+ if (info->rx_skb != NULL) {
+ dev_err(info->dev, "Receive timed out, %i done, %li left, "
+ "LSR=%02x, IER=%02x\n", info->rx_skb->len + 1,
+ info->rx_count, hci_h4p_inb(info, UART_LSR),
+ hci_h4p_inb(info, UART_IER));
+ info->rx_timed_out = 1;
+ }
Could you share your rationale for that comment in drivers/bluetooth/hci_h4p/core.c? (Oh and there's a typo, too :P )
EDIT: Asking this because commenting that block out changed status of bluetooth (for me) from unusable (can receive ~20-500kB of data before ppp connection halting) to fully working - used to have big problems playing 32kbps AAC stream (max 2 min), now already 4 mins of 96kbps, but i still think we need some receive timeout mechanism, but this one (as it currently stands) doesnt work.
Notaz's reply:
I don't really remember, it was more than 1.5 years ago. That driver is a hack, will need to review it, does it work stable with that code removed?
My reply:
For the non-IRC people:
urjaman on IRC said:
(22:47:45) urjaman: notaz: about stability: i'm on irc atm with that driver, its been playing internet radio for a few hours without problems now, but i don know for sure.
(22:48:00) urjaman: *dont know
(22:50:11) urjaman: my logic: if the serial port _never_ misses a byte it should be ok - IMO scary without some receive timeout, but works for me |
|
72 | Core | Bug Report | Medium | Automatic Screen Saver crashes SGX Apps | Closed | |
Task Description
The automatic screen saver crashes apps which use the new SGX driver.
Has been tested with pmenu and Quake.
This does NOT happen with the Lid close / open turn off-routine, just with that automatic screen saver that turns of the LCD when you don't press a button for a while. |
|
99 | Core | Bug Report | Medium | After waking up from standby the system is not responsi ... | Closed | |
Task Description
If I resume after standby (moved the slider to the right), the pandora shows the desktop and I can move the mouse cursor but if I click something, nothing happens.
IRC suggested that the CPU might still be clocked at the standby low power speed. |
|
317 | Core | Bug Report | Medium | After disabling USB-host current still flows into USB d ... | Closed | |
Task Description
On my Pandora, due to bad internal WiFi, I use an Edimax EW-7811Un USB WiFi adapter, which has a status-LED, flickering according to the network activity.
After disabling USB-host through the settings menu, the WiFi functionality is gone, but the device's LED is still on. So some current must still flow into the USB device.
The LED now has a permanent light, no flickering! This lack of "device intelligence" indicates that the device was indeed turned off, just current flowing directly to the LED circuit unaltered).
I can repeat the aforementioned steps many times, the behavior is the same.
As soon as I then first physically unplug and reinsert the device, the LED remains off eventually.
From then on, every further issuing of "Disable USB-host" through the settings menu turns the device LED completely off.
Smells like a kernel bug to me! As it requires one real un/re-plugging, from then on works ok. |
|
225 | Core | Bug Report | Medium | ads7846 reports odd pressure values | Unconfirmed | |
Task Description
using evdev xorg drivers and not the tslib drivers you can receive pressure axis data however there is
a problem with the values reported by the ads7846 module and the evdev driver has no calibration property for pressure
using
xinput test touchscreen
you can see the pressure axis ranging from 120-ish for hard press to about 150-170 for light press (low pressure values can
be quite erratic)
I could possibly hack the evdev module to possibly do something with this odd and narrow range of values, but I rather think looking
at the source that the ads7846 module needs some work.
is there a git tag that has a known working configuration? as I've had problems getting the kernel to compile the last few times I attempted... |
|
221 | Core | Bug Report | Medium | 32MB worth of qt4 examples in /usr/bin/qt4 ? | Closed | |
Task Description
Hi, after upgrading to HF5, I accidentally discovered that there are 32MB of qt4 examples & demos in directory /usr/bin/qt4, those examples do work. For instance the /usr/bin/qt4/examples/webkit/fancybrowser/fancybrowser is a working WWW browser.
It is, without any dispute a very useful qt4 development help, but are you sure that you want to include all that in NAND ? |
|
112 | Core | Bug Report | Medium | .pnd files with spaces in filename won't work | Closed | |
Task Description
pnd_run.sh barfs when given a file with space in it's name.
Also pnd_run bin doesnt enclose the .pnd name, it should.
/usr/pandora/scripts/pnd_run.sh -p "PicoDrive_180beta2 .pnd" -e PicoDrive.run
pnd set to `PicoDrive_180beta2 .pnd'
exec set to `PicoDrive.run'
/usr/pandora/scripts/pnd_run.sh: line 50: [: PicoDrive_180beta2: unary operator expected
when run from menu:
in fork!
df: /media/mmcblk1p1/pandora/desktop//PicoDrive_180beta2: can't find mount point
mountpoint:
/usr/pandora/scripts/pnd_run.sh: line 120: [: !: integer expression expected
not mounted on loop yet, doing so
Usage: grep [OPTION]... PATTERN [FILE]...
Try `grep --help' for more information.
Usage: grep [OPTION]... PATTERN [FILE]...
Try `grep --help' for more information.
error determining fs, output was cannot |
|
289 | Application | Bug Report | Medium | "sudo find /" produces assertion | Closed | |
Task Description
$ sudo find /
find: ftsfind.c:477: consider_visiting: Assertion `ent->fts_info == 11 || state.type != 0' failed.
Aborted
This is fixed by updating findutils to latest version using
sudo opkg upgrade findutils
Release SuperZaxxon 1.5
(not Beta 3, as given in "Reported Version" field, but there the release cannot be chosen). |
|
130 | Core | Feature Request | Low | [PATCH] in vsense mbuttons mode down=middle click | Closed | |
Task Description
Patch attached. |
|
153 | Application | Feature Request | Low | [PATCH] HACK: change OPP level according to set Mhz | Closed | |
Task Description
It's a hack, use on your own risk as always. I feel like abusing the tracker dropping all my patches here, but whatever. Patch attached. |
|
305 | Core | Bug Report | Low | [PATCH] bluetooth startup doesnt restore enabled state | Closed | |
Task Description
op_bluetooth.sh doesnt remember to call op_bluetooth_work.sh in the startup case. Patch inlined here (maybe broken, but for fast reading) and behind link: http://urjaman.dyndns.info/bluetooth-startup-fix.patch
--- op_bluetooth.sh.org 2012-11-24 01:54:53.000000000 +0000
+++ op_bluetooth.sh 2012-11-24 02:06:51.000000000 +0000
@@ -7,8 +7,13 @@
cd "$HOME"
if [ "$1" = "startup" ]; then
- [ -f "$LOCK" ] && sudo /usr/sbin/hciconfig "$INTERFACE" up pscan 1>/dev/null && sudo /usr/sbin/bluetoothd || echo "Bluetooth: User has not enabled Bluetooth."
-
+ if [ -f "$LOCK" ]; then
+ sudo /usr/pandora/scripts/op_bluetooth_work.sh 1
+ INTERFACE="`hciconfig | grep "^hci" | cut -d ':' -f 1`"
+ sudo /usr/sbin/hciconfig "$INTERFACE" up pscan 1>/dev/null && sudo /usr/sbin/bluetoothd
+ else
+ echo "Bluetooth: User has not enabled Bluetooth."
+ fi
else
# Figure out if Bluetooth is running or not |
|
93 | Base OS | Bug Report | Low | zaxxon first boot: don't ask for user prompt if already ... | Closed | |
Task Description
How to reproduce:
First boot, Pandora's Box has been opened. Prompt for Full name, username, and password.
Then, simply press OK without selecting whether minimenu or xfce. None selected. Then you can't do any more. Wizard closes and you don't need any more options.
After manual reboot, the wizard starts again and asks for name again. But the username already exists. |
|
185 | Core | Bug Report | Low | Xorg driver should not be dependant on user environment | Unconfirmed | |
Task Description
The patch implementing screen blanking uses the /usr/pandora/scripts/op_lid.sh script to control LCD backlit:
http://git.openpandora.org/cgi-bin/gitweb.cgi?p=openembedded.git;a=blob;f=recipes/xorg-driver/xf86-video-omapfb/pandora_backlight_dim.patch;h=4a0b8432d083c6e7297192a2920c7a777ae3d098;hb=16f3fff44323bd6b4349d909667b51a2fef3f278
The same result can be achieved by using the sys interface:
/sys/devices/platform/twl4030-pwm0-bl/backlight/twl4030-pwm0-bl/bl_power
This approach makes driver independent on particular distribution. The proposed patch is attached. |
|
27 | Core | Bug Report | Low | xfce4-brightness-plugin: 0 isn't a good minimum value | Closed | |
Task Description
The xfce4-brightness-plugin can be set to a minimum of 0.
This is kinda confusing to the normal user, as it makes the screen totally black.
Maybe this could be changed to a minimum of 3? |
|
19 | Core | Feature Request | Low | XFCE-Menu Editor | Closed | |
Task Description
Add an XFCE-Menu Editor (using python).
This way, people can edit the Startmenu :)
http://my.opera.com/Texel/blog/2008/02/20/xfce-applications-menu-editor-0-4 |
|
326 | Core | Bug Report | Low | XFCE menu not expandingl with stylys and scrolling brok... | Unconfirmed | |
Task Description
The XFCE menu does not always show submenues like "Emulators" when being clicked on with the stylus. It only works if the click lasts long or after all menues have been clicked at once with a long click.
Also, tipping on a scroll arrof of menues that are higher than the screen causes the click to be registered as a "click and hold". This leads to the menu being scrolled all the way to the end. |
|
328 | Core | Bug Report | Low | XFCE desktop icons not displayed when logging on too qu... | Requires testing | |
Task Description
It looks like XFCE cannot find the icons for links/launchers on the desktop, when the user logs on too quickly. This happens either when the session chooser at start-up is disabled, or when the session is being chosen quickly after the session chooser is being displayed (e.g. by pressing enter as soon as the chooser window pops up). The icons are probably not generated yet at that time point.
A simple workaround is adding the command "xfdesktop --reload" to autostart. Couls this be included in the next SuperZaxxon release or a hotfix? |
|
211 | Core | Bug Report | Low | x11vnc server (in xfce menu - > network) does not work! | Closed | |
Task Description
x11vnc launcher in xfce menu -> network does not work.
can this be fixed please. |
