OpenPandora Main OS

This project it to track issues relating to the current shipping OS only as found here http://goo.gl/S5JCy. Please state what Hotfix you are running with any issue report. Please ONLY use this to record issues for the main OS and its default included applications - any other application issue reports should go into the Additional Applications project. Issue reports with 'in development OS images' or feature requests for the next MAJOR version (not Hotfix release) should be placed into the OpenPandora Development OS project and reported on the mailing list http://openpandora.org/cgi-bin/mailman/listinfo/firmware-dev. Please read this page to find out how to properly report bugs: http://pandorawiki.org/Reporting_bugs

ID  descCategoryTask TypeSeveritySummaryStatusProgress
 215 CoreBug ReportMedium Kingston 32GB Class6G2 SDHC card not working in pandora Closed
100%
Task Description I have noticed errors like this, but not every time [ 1455.612792] mmc2: card claims to support voltages below the defined range. These will be ignored. [ 1455.621795] mmc2: SDIO card claims to support the incompletely defined 'low voltage range'. This will be ignored. [ 1455.665985] mmc2: new SDIO card at address 0001 This is me plugging in my 32GB SD6G2 Kingston SDHC card. at [ 1114.484252] is when the file copy started Errors continue from there until it bombs and remounts the filesystem readonly. I have tried this with ext3 vfat in various configurations and all fail the same I/O errors Let me know if I can do anything to help ------------------------------------- [ 989.496459] mmc1: host does not support reading read-only switch. assuming write-enable. [ 989.504638] mmc1: new high speed SDHC card at address 0003 [ 989.510620] mmcblk1: mmc1:0003 SD32G 31514112KiB [ 989.515625] mmcblk1: p1 p2 p3 p4 < p5 p6 > [ 989.940490] FAT: invalid media value (0x00) [ 989.944702] VFS: Can't find a valid FAT filesystem on dev mmcblk1. [ 990.083190] FAT: invalid media value (0x00) [ 990.087402] VFS: Can't find a valid FAT filesystem on dev mmcblk1. [ 991.907562] EXT3-fs: Unrecognized mount option "umask=0" or missing value [ 991.922943] EXT3-fs: Unrecognized mount option "umask=0" or missing value [ 992.002563] mmci-omap mmci-omap.0: MMC IRQ 0x208002 : TC ERRI DCRC [ 992.003143] mmcblk0: retrying using single block read [ 992.028411] kjournald starting. Commit interval 5 seconds [ 992.048553] EXT3-fs: Unrecognized mount option "umask=0" or missing value [ 992.092346] kjournald starting. Commit interval 5 seconds [ 992.237091] kjournald starting. Commit interval 5 seconds [ 992.259185] EXT3-fs: Unrecognized mount option "umask=0" or missing value [ 992.361999] FAT: bogus number of reserved sectors [ 992.366760] VFS: Can't find a valid FAT filesystem on dev mmcblk1p4. [ 992.400909] kjournald starting. Commit interval 5 seconds [ 992.612945] EXT3 FS on mmcblk1p2, internal journal [ 992.617797] EXT3-fs: mounted filesystem with ordered data mode. [ 992.787475] EXT3 FS on mmcblk1p3, internal journal [ 992.792449] EXT3-fs: mounted filesystem with ordered data mode. [ 993.038940] EXT3 FS on mmcblk1p1, internal journal [ 993.043884] EXT3-fs: mounted filesystem with ordered data mode. [ 993.205749] EXT3 FS on mmcblk1p5, internal journal [ 993.210632] EXT3-fs: mounted filesystem with ordered data mode. [ 993.510253] FAT: bogus number of reserved sectors [ 993.515045] VFS: Can't find a valid FAT filesystem on dev mmcblk1p4. [ 1114.484252] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1114.484802] mmcblk0: retrying using single block read [ 1115.763946] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1115.765594] mmcblk0: retrying using single block read [ 1115.984649] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1115.984985] mmcblk0: retrying using single block read [ 1116.039489] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1116.039916] mmcblk0: retrying using single block read [ 1116.094329] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1116.094757] mmcblk0: retrying using single block read [ 1116.150146] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1116.152343] mmcblk0: retrying using single block read [ 1116.212127] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1116.212615] mmcblk0: retrying using single block read [ 1116.267791] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1116.268280] mmcblk0: retrying using single block read [ 1116.335723] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1116.337738] mmcblk0: retrying using single block read [ 1116.410766] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1116.413360] mmcblk0: retrying using single block read [ 1116.488250] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1116.490234] mmcblk0: retrying using single block read [ 1116.581390] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1116.581939] mmcblk0: retrying using single block read [ 1116.645721] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1116.646331] mmcblk0: retrying using single block read [ 1116.933288] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1116.933715] mmcblk0: retrying using single block read [ 1117.000518] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1117.002899] mmcblk0: retrying using single block read [ 1117.068328] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1117.070526] mmcblk0: retrying using single block read [ 1117.128326] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1117.128753] mmcblk0: retrying using single block read [ 1117.194183] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1117.194488] mmcblk0: retrying using single block read [ 1117.261566] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1117.262084] mmcblk0: retrying using single block read [ 1117.328674] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1117.329956] mmcblk0: retrying using single block read [ 1117.388061] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1117.390380] mmcblk0: retrying using single block read [ 1117.451629] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1117.452087] mmcblk0: retrying using single block read [ 1117.510467] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1117.512725] mmcblk0: retrying using single block read [ 1117.714874] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1117.715301] mmcblk0: retrying using single block read [ 1117.776550] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1117.778930] mmcblk0: retrying using single block read [ 1117.841247] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1117.841674] mmcblk0: retrying using single block read [ 1122.718658] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1122.719055] mmcblk0: retrying using single block read [ 1123.265136] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1123.265441] mmcblk0: retrying using single block read [ 1123.442230] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1123.442413] mmcblk0: retrying using single block read [ 1126.759338] mmci-omap mmci-omap.1: MMC IRQ 0x108000 : ERRI DTO [ 1126.759399] mmcblk1: error -110 transferring data, sector 32669824, nr 8, card status 0xc00 [ 1126.807830] mmci-omap mmci-omap.1: MMC IRQ 0x108000 : ERRI DTO [ 1126.807891] end_request: I/O error, dev mmcblk1, sector 32669824 [ 1126.813934] Buffer I/O error on device mmcblk1p1, logical block 4083726 [ 1126.820556] lost page write due to I/O error on mmcblk1p1 [ 1127.630950] mmci-omap mmci-omap.1: MMC IRQ 0x108000 : ERRI DTO [ 1127.631011] mmcblk1: error -110 transferring data, sector 32686232, nr 8, card status 0xc00 [ 1127.715179] mmci-omap mmci-omap.1: MMC IRQ 0x108000 : ERRI DTO [ 1127.715240] end_request: I/O error, dev mmcblk1, sector 32686232 [ 1127.721282] Buffer I/O error on device mmcblk1p1, logical block 4085777 [ 1127.727935] lost page write due to I/O error on mmcblk1p1 [ 1133.399963] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1133.400024] Spurious DMA IRQ [ 1133.403411] mmcblk0: retrying using single block read [ 1133.504821] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1133.504943] mmcblk0: retrying using single block read [ 1133.599304] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1133.599548] mmcblk0: retrying using single block read [ 1133.767486] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1133.767578] mmcblk0: retrying using single block read [ 1134.222564] mmci-omap mmci-omap.0: MMC IRQ 0x208000 : ERRI DCRC [ 1137.074981] mmcblk0: retrying using single block read [ 1137.465576] mmci-omap mmci-omap.1: MMC IRQ 0x108000 : ERRI DTO [ 1137.465667] mmcblk1: error -110 transferring data, sector 17316672, nr 72, card status 0xc00 [ 1137.509582] mmci-omap mmci-omap.1: MMC IRQ 0x108000 : ERRI DTO [ 1137.509643] end_request: I/O error, dev mmcblk1, sector 17316672 [ 1137.515686] end_request: I/O error, dev mmcblk1, sector 17316680 [ 1137.521728] end_request: I/O error, dev mmcblk1, sector 17316688 [ 1137.527770] end_request: I/O error, dev mmcblk1, sector 17316696 [ 1137.533813] end_request: I/O error, dev mmcblk1, sector 17316704 [ 1137.539855] end_request: I/O error, dev mmcblk1, sector 17316712 [ 1137.545867] end_request: I/O error, dev mmcblk1, sector 17316720 [ 1137.551910] end_request: I/O error, dev mmcblk1, sector 17316728 [ 1137.557952] end_request: I/O error, dev mmcblk1, sector 17316736 [ 1137.766906] Aborting journal on device mmcblk1p1. [ 1137.997436] journal commit I/O error [ 1138.001037] EXT3-fs error (device mmcblk1p1) in ext3_create: IO failure [ 1138.225067] ext3_abort called. [ 1138.228149] EXT3-fs error (device mmcblk1p1): ext3_journal_start_sb: Detected aborted journal [ 1138.236785] Remounting filesystem read-only
 214 CoreBug ReportHigh op_wifi pnd not exiting cleanly, with fix (one characte ...Closed
100%
Task Description The op_wifi pnd does not exit out cleanly once the encased script executes, the pndrun_op_wifi.out reports umount: /mnt/utmp/op_wifi: device is busy. umount: /mnt/utmp/op_wifi: device is busy. umount UNION failed, didn't clean up. Process still using this FS : 3197 ? S 0:00 /bin/sh /etc/init.d/wl1251-init start This op_wifi.sh just calls /usr/pandora/scripts/op_wifi.sh for some reason, the init.d/w.... start causes it to hang, I executed all this locally, and it doesn't appear to keep running Appending " &" to the line which calls this init script, solves the problem.
 213 ApplicationBug ReportLow Gigolo does not perform it's task Closed
100%
Task Description In it's current state, Gigolo is flat out broken and (almost) useless. It pretends to to it's job, but can't because it's missing critical pieces of anatomy. It can mount local filesystems correctly, but then so can thunar, so this is a redundant and useless function. The main reason to use Gigolo is to mount remote filesystems easily, and without having to use the terminal, and to save passwords in your keychain. The solution to the problem is to perform the following tasks: sudo opkg install gvfsd-sftp sshfs-fuse sudo mousepad /etc/modutils/fuse type "fuse" save and quit sudo update-modules
 212 CoreFeature RequestLow Add curl to core installed programs Closed
100%
Task Description I wish for curl to be installed by default on the upcoming pandora FWs, As reported by the angstrom repo, where I install using the command: $sudo su ... #opkg update #opkg install curl curl 7.21.2-r4.0.9 is 78.57 Kilobytes with the dependencies Depends:libcurl4, libgnutls26, libgcrypt11, libgpg-error0, libc6, libz1 I do not know which is installed by default, but I'm sure libc6 is, so I'm going to state the info on the rest of the packages for its memory space usage on the NAND libcurl4(142.99 Kilobytes): Command line tool and library for client-side URL transfers. Depends:libc6, libgnutls26, libz1, libgcrypt11, libgpg-error0, as you can see, it has the same dependencies as above, so it seems both curl and libcurl are probably exclusive from the others, but I will go forward and state the rest of the dependencies libgnutls26 2.8.6-r10.0.5 (291.44 Kilobytes) Depends:libz1, libgcrypt11, libgpg-error0, libc6, (again, it looks like the above depends on this) libgcrypt11 1.4.1-r0.9 (220.35 Kilobytes) Depends: libgpg-error0, libc6, (Oh look, we're not looking at libz1 anymore) libgpg-error0 1.4-r7.1.9 (5.78 Kilobytes) Depends:libc6 now to the lone libz1 libz1 1.2.3-r7.0.9 (41.95 Kilobytes) Depends:libc6 So, in the case we already have the gpg stuff, then the installation is only 221.56KB, however, with the zlib and the gpg included, the total comes to 781.08KB So, now that the cost is out of the way, What are the goods and bads? Good: Its a very versatile CLI program to get and send information over http through the network, and is tolerant of network issues It doesn't take too much space relative to things that have been pulled out, like abiword. The libcurl is a very good library, and could be of great benefit to some future projects. Bad: Well, we already have wget, which is not as configurable, and wget hates Craig's appstore Here's the link to curl on the repo http://www.angstrom-distribution.org/repo/?pkgname=curl
 211 CoreBug ReportLow x11vnc server (in xfce menu - > network) does not work! Closed
100%
Task Description x11vnc launcher in xfce menu -> network does not work. can this be fixed please.
210CoreFeature RequestMediumWader - cross platform graphical assistant for 3g conne...Unconfirmed
0%
Task Description http://www.wader-project.org http://trac.wader-project.org http://trac.wader-project.org/wiki/Developers this would be really usefull to monitor reception/network of mobile broadband dongle and it also counts ur mobile data usage (for those that have limits).
209CoreFeature RequestMediumShutdown after a full chargeUnconfirmed
0%
Task Description That still need to be configurable, but chris_c does a good job I'ld like to see integraded in the main image : http://www.gp32x.com/board/index.php?/topic/58794-a-script-to-shutdown-after-charging/ and : http://chrisc.bedroomcoders.co.uk/?p=77
 208 CoreBug ReportCritical HOTFIX 4 and 5 Slow WIFI Closed
100%
Task Description I'm getting 5kb/s with bursts up to 10kb/s if I am lucky. I have attempted every channel on my router. Tried every encryption even no encryption. Tested with the router's wifi speed: 300Mbps 154Mbps and 45Mbps I'm running Hotfix 5 RC2. Wifi works fine with my android smartphone, and other wireless devices such as a laptop.
 207 CoreBug ReportMedium Touchscreen calibration / use of nubs conflict Closed
100%
Task Description When using certain apps like Basilisk 2 / Dosbox / Enigma the analogue stick and touchscreen are both available to use as a mouse cursor. All is well with the touch until you decide to touch the analogue stick when then affects touchscreen alignment by about 2 - 3 CM. This has been going on since first release.
 205 CoreBug ReportMedium libpnd functions and dynamic libs missing Closed
100%
Task Description tried to compile a simple test application that uses functions from libpnd, namely pnd_evdev_open(pnd_evdev_e) pnd_evdev_dpad_state(pnd_evdev_e) pnd_evdev_closeall() but all 3 seem to be missing. yes, i'm linking to libpnd ... but no chance to get it running. i'm using ivanovic's latest toolchain, which in turn installs "pandora-libpnd-dev_1.0-r40.5_armv7a.ipk" ... also, there's only the static library available inside, no dynamic libraries.
204CoreBug ReportMediumfonts issuesUnconfirmed
0%
Task Description Ok, I just want to say that there is something missing about the font on the base image. I cant get what (at least for now) Here is an issue : http://www.gp32x.com/board/index.php?/topic/54282-getting-vnc-viewer-to-work/ With my current Ogre build I get : Warning: Unable to load any usable ISO8859 font Error: Aborting: no font found I've googled but so far no solution :(
 203 CoreBug ReportLow Video-out setting window does not exit on OK Closed
100%
Task Description The "video-out" window opens again if you choose OK button.
 202 CoreBug ReportLow Set Date and Time won't let you cancel or close Closed
100%
Task Description The Date and Time application in MiniMenu by won't let you use the cross or the cancel button to close the application without changing anything. If you use one of those buttons then a new window opens that says: "Error: Please select a timezone" and equally so for the date and time.
 201 CoreBug ReportHigh PND apps still use memory after they've quit Closed
100%
Task Description After running and quitting a PND app, not all of the used memory is being freed. This eats more and more memory over time. Just run 5 or 6 apps and you only have half of the memory left. Sounds like either aufs or unionfs don't free the memory after unmounting. This has been reported with HF4 and still is the case with HF5 Beta 2 -- downgraded to 'Researching' and 'Normal' priority until confirmed and details found
 200 CoreBug ReportLow After opening the lid, the backlight is not reset to th ...Closed
100%
Task Description Using the hotkeys to set the backlite, after closing and then opening the lid, the backlight is not reset to the same level it was before closing it. It seems to set it to a fixed value.
 198 ApplicationBug ReportLow Mousepad: 'Find' works only once Closed
100%
Task Description Mousepad 0.2.16 Find (Ctrl+F) works once, the next time it is used the button 'Find' is and stays grayed out.
 197 CoreBug ReportHigh [PATCH] Fix opp if booting with wrong settings in hw Closed
100%
Task Description Hi, This should help with cases like this http://www.gp32x.com/board/index.php?/topic/57303-overclocking-broke-my-pandora/ Patch attached.
 196 CoreFeature RequestMedium [PATCH] Add tablet support into kernel Closed
100%
Task Description Hi, This should be a quite simple thing, but my first time touching the OE repo and i cant test it, so be careful.
 195 CoreFeature RequestHigh Start re-recharge of battery sooner Closed
100%
Task Description Increase battery LVL_4 and LVL_3 threshold. After reaching 100%, in some cases the charge circuit enters "battery full" state, stops charging, and begins to discharge. This is not entirely unexpected behavior according to the spec sheet, although I don't fully understand exactly the situations in which it completes charging. Once the battery is full, the battery will begin discharging. The charge circuit automatically restarts the recharge once the voltage has gone below a certain level (crosses below the LVL_3 voltage threshold) The default LVL_3 voltage threshold is 3.902 volts which is at about 80-85% battery level as recorded by bq27500 chip. In my opinion, this is way too low. Setting the BCIMFTH2 register to 0xCB increases the voltage threshold to about 4.003 volts which is about 93%. Setting it to 0xDC may also be worthwhile, which is just over 95%. By default, if a user leaves their Pandora plugged in overnight, they may wake up to find their Pandora has stopped charging and the capacity has dropped to almost 80%, which can be quite startling to some users who will then report it as a bug. This change will ensure that it never drops below 93-95%, a much more acceptable level. Specific code changes suggested, in the /drivers/power/twl4030_bci_battery.c file, somewhere in the twl4030_bci_battery_probe function (or a function called by it), add the lines: /********************************/ #define KEY_FTH2 0x7F #define REG_BCIMFTH2 0x017 ret = twl4030_i2c_write_u8(TWL4030_MODULE_MAIN_CHARGE, KEY_FTH2, REG_BCIMFKEY); if (ret) return ret; ret = twl4030_i2c_write_u8(TWL4030_MODULE_MAIN_CHARGE, 0xDC, REG_BCIMFTH2); if (ret) return ret; /********************************/ (Move defines to the top, as appropriate)
 194 CoreBug ReportLow python ctypes broken (and fix) Closed
100%
Task Description run python and type import ctypes cant find _ctypes it says.... for further details and a fix see http://www.gp32x.com/board/index.php?/topic/57102-python-ctypes-stopped-working/
 193 CoreBug ReportLow Cannot reach button well in ubuntu x64 Closed
100%
Task Description Window can also not be resized
 192 CoreBug ReportMedium [U-Boot] ext2fs_devread() read error - block (boot from ...Closed
100%
Task Description [U-Boot] ext2fs_devread() read error - block Description: Formatted two different Transcend 8GB SD cards as EXT2 using both GParted and also with Mkfs.ext2, extracted pandora-rootfs.tar.bz2 to the root of the SD and added 'autoboot.txt' as described here: http://openpandora.org/firmware/README.txt This issue appears to be same as mentioned here, looks like a patch maybe required in drivers/mmc/omap3_mmc.c): http://lists.denx.de/pipermail/u-boot/2010-June/072198.html Output on boot : mmc1 is available reading autoboot.txt ** Unable to read "autoboot.txt" from mc1 0:1 ** Loading file "autoboot.txt" from mmc1 device 0:! (xxa1) 184 bytes read ** Executing plain script at 82000000 Loading file "/boot/uImage-2.6.27.46-omap1" from mmc device 0:1 (xxa1) ** ext2fs_devread() read error - block ** Unable to read "/boot/uImage-2.6.27.46-omap1" from mmc 0:1 ** ## Booting kernel from Legacy Image at 8030000 ... Image Name: Angstrom/2.6.27-pandora+r21+git4 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2325740 Bytes = 2.2 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... Bad Data CRC ERROR: can't get kernel image! syntax error
190CoreBug ReportMediumRemoving desktop-shortkeys does not workUnconfirmed
0%
Task Description Try clearing shortcuts in Start->Settings->Window Manager->Keyboard. That doesn't work (for me). This is a problem because these shortcuts are blocking key-combination in apps, like for example the keymapper in dosbox (CTRL+F1) or refreshing content (CTRL+F5). I tried manual editing or even deleting the configuration file, but changes are not recognized and the file recreated on reboot.
 189 CoreBug ReportMedium pnd-run.sh does not work correctly for very long <pathn ...Closed
100%
Task Description When unmounting, the pnd-run-script greps the output of "losetup -a" at some point. But if you have a very long pathname and filename for the pnd (like "/media/trans8/gamedata/scummvm/Secret_of_Monkey_Islands_Amiga_EN.pnd" then the endpart is cut off in the output, grep can't find the right part and the script get's confused. Example: mounting works: /usr/pandora/scripts/pnd_run.sh -p /media/trans8/gamedata/scummvm/Secret_of_Monkey_Islands_Amiga_EN.pnd -b scummvm -m unounting does not work: /usr/pandora/scripts/pnd_run.sh -p /media/trans8/gamedata/scummvm/Secret_of_Monkey_Islands_Amiga_EN.pnd -b scummvm -u (see /tmp/pndrun*-logs for output) The problem is that the outut of losetup looks like this in such a case: "/dev/loop7: [b309]:157081 (/media/trans8/gamedata/scummvm/Secret_of_Monkey_Islands_Amiga_*)" And because the pnd-name is not fully shown, grepping the name does not work. After i renamed th pnd to a much shorter name (somi_amiga_en.pnd) it worked nicely. Still this should be fixed.
 188 CoreBug ReportHigh "rdate" sets the time exactly 3 hours in advance Closed
100%
Task Description "rdate -s time.ien.it" will set the date (hour) 3 hours in advance. The time (and timezone) can be adjusted manually using the "Settings -> Date and Time" tool, but on the next rdate-update the issue will occur again
 187 CoreBug ReportHigh LCD turns off after "rdate" updated the date Closed
100%
Task Description running "sudo rdate -s time.ien.it" will set the brightness of the LCD to 0. User has to use FN + I to increase it back to a usable level. "rdate" asks for the super-user password as expected, updates the date as expected, but turns off the screen.
 186 ApplicationBug ReportMedium unusable "Manage LCD Gamma" tool Closed
100%
Task Description Pandora Menu -> Settings -> LCD-Settings -> Manage LCD Gamma Removing all the profiles listed there will make the user unable to even create a new one. The tool becomes unusable. I hope a re-flash would fix the problem. The last profile in the list, or the Default one, shouldn't be deletable at all.
185CoreBug ReportLowXorg driver should not be dependant on user environmentUnconfirmed
0%
Task Description The patch implementing screen blanking uses the /usr/pandora/scripts/op_lid.sh script to control LCD backlit: http://git.openpandora.org/cgi-bin/gitweb.cgi?p=openembedded.git;a=blob;f=recipes/xorg-driver/xf86-video-omapfb/pandora_backlight_dim.patch;h=4a0b8432d083c6e7297192a2920c7a777ae3d098;hb=16f3fff44323bd6b4349d909667b51a2fef3f278 The same result can be achieved by using the sys interface: /sys/devices/platform/twl4030-pwm0-bl/backlight/twl4030-pwm0-bl/bl_power This approach makes driver independent on particular distribution. The proposed patch is attached.
 184 CoreFeature RequestMedium libpnd: Add a function to get all mounted PNDs Closed
100%
Task Description Add a function to get all mounted PNDs. Because it's very annoying to check all the menu/desktop folders on all of the SD-Cards.
 183 CoreBug ReportHigh Left mouse click and hold = fail Closed
100%
Task Description When I want to hold and select multiple files its not working. Not with the nubs or the touchscreen. I can try an easy test by making the select rectangle on the desktop. It only becomes very very tiny. If I try very fast diagonal drag motion on the touchscreen. It becomes a little larger. Trying to grab scrollbar is the same issue.
 182 CoreBug ReportMedium Ctrl + F5 (Fn Lock) Fail Closed
100%
Task Description So I've tried this a while now with no success. I'm assuming its when Fn is triggered and then pressing Ctrl or Alt it goes away.
 181 ApplicationBug ReportLow Triple click in Thunar crash Closed
100%
Task Description Triple tapping (with the stylus) a directory in Thunar in icon or compact mode (not detail view) causes Thunar to close (crash) This is consistently repeatable: tapping three times in rapid succession on the same spot of the file causes the crash. It must be the exact same spot, as if double clicking, but a third tap is added. This can be triggered especially when a user becomes frustrated at mistapping, gets carried away, and taps too much.
 180 CoreBug ReportMedium LCD Brightness Lower = Flashing, Dies. Closed
100%
Task Description Just try and lower with the Fn+Br- until it starts to flashing and just dies if you go lower. It does go back if you raise it again. Feels wrong. Also no real feel in the brightness getting lower.
179CoreBug ReportLow.vimrc-preset for user but not for rootUnconfirmed
0%
Task Description I am running PandoraOS from sd-card installed with the official tarball "pandora-rootfs.tar.bz2". I noticed that the control/keyboard-mapping in vi does not work correctly after switching to root (for example sudo su-). I solved this by copying over my users .vimrc to root-homedir. This should already be included in the tarball.
178CoreBug ReportLowMount-loop when booting from SD-cardUnconfirmed
0%
Task Description When booting the pandora-OS from sd-card by using the official tar, you will end up with your sd-card being mounted twice: once as / and once as /media/. I solved this by adding "/dev/mmcblk0" to "/etc/udev/mount.blacklist". Maybe this should be added to the default tarball? I'm not sure as it might be used in other ways maybe (beside SD-card-installation)? Background: I ran "updatedb" as root and have been notified by a message that there was a mount-loop. After adding the above modification the system still booted fine and "updatedb" ran nicely without a warning.
 177 CoreBug ReportMedium no x or xfce after shutdown and reboot Closed
100%
Task Description often but not always after shutting down the system (xfce logout, choose shutdown) thereĀ“s a problem when booting again. i got the normal bootscreen but when x an xfce should start the screen remains black. i cannot say if the x or xfce didnĀ“ start or if it is a problem with the backlight intensity. rebooting with pandora key and power key leads to the same situation. the only thing that seems to help is to remove the battery shortly. so, what is the difference beetween reboot after powerdown and reboot after replacing the battery? there could be the point to fix this problem.
 176 CoreBug ReportMedium op_power.sh: problematic display brightness restoring a ...Closed
100%
Task Description Since hotfix4 it is possible to reduce the value for display brightness below '3'. Thus the script op_power.sh (the one used for low power mode) has to be adjusted accordingly. Currently line 25 in this script looks like this: if [ $oldbright -ge 3 ] && [ $oldbright -le $maxbright ]; then Please change the "-ge 3" part to "-ge 1" so that lower modes are possible, too. Otherwise the screen will be set to max brightness if you have selected a value of '1' when going into powersave mode. Somehow it looks like what is possible to select via the hotkeys and what is possible via the "application" differs. In the script op_lcdsettings.sh in line 11 a minimum brightness of 3 seems to be defined, with the hotkeys it is even possible to go down to 0 (screen off) or values like 1 and 2. This is the relevant line: minbright=3 Brightness restoring appears to be problematic in op_lid.sh, too. Just have a look at line 25 in this script: if [ $oldbright -ge 3 ] && [ $oldbright -le $maxbright ]; then Another issue is that the clockrate of 14MHz is simply too low to be reasonable. Please do adjust it to 125MHz instead, since this seems to be what TI recommends and what makes most sense since starting with hotfix4 this is where the lowest powermode (OPP0) is entered. When clocking down to 14MHz issues like the clock not working correctly come up. Relevant lines in op_power.sh: line 14, restoring old clockrate: if [ $oldspeed -gt 14 ] && [ $oldspeed -le 900 ]; then line 72, setting the clockrate for low power mode: echo 14 > /proc/pandora/cpu_mhz_max
 175 CoreTo Do (Reminder)Very Low Test Closed
100%
Task Description Test if the edit button in the bug tracker works now. //Edit: Blah
 174 Base OSFeature RequestLow Include modem-manager in base image Closed
100%
Task Description Please consider including the modemmanager package in the base distibution. This allows 3G wireless dongles to work out of the box (configured via network-manager).
 173 CoreBug ReportHigh X uses 100% cpu in low power mode Closed
100%
Task Description After 10 minutes in low power mode X seems to go nuts and use 100% CPU. Obviously this is bad ;-) 14MHz isn't *that* slow, so there's obviously something getting wedged. I haven't been able to figure out exactly what's happening, but the fact that it always occurs after exactly 10 minutes suggests its power management related. Maybe we're getting stuck trying to kick off the screensaver, or something? Hacking op_power.sh do disable screen blanking shows that, unsurprisingly, the screen freezes at the same time X goes AWOL. Pressing the power switch brings the device out of low power mode, though there is often a few seconds additional delay as the event handling scripts take longer than normal to run because the CPU is already busy. I've attached the results of top -b -d 60 > toplog & while sleep 60 ; do cat /proc/loadavg; done > loadlog
 172 CoreBug ReportLow Angstrom repo's bison is borked (FYI) Closed
100%
Task Description This is how it tries to call m4 (strace -fF'd): [pid 4231] execve("/OE/angstrom-dev/sysroots/x86_64-linux/usr/bin/m4", ["/OE/angstrom-dev/sysroots/x86_64"..., "/usr/share/bison/m4sugar/m4sugar"..., "-", "/usr/share/bison/yacc.c"], [/* 38 vars */]) = -1 ENOENT (No such file or directory) Problem = obvious. This is here because a) it is the bison that i get with opkg install bison and b) because i could find a general purpose bugtracker for stuff in the angstrom repo with a single googling. Added info on bison version, etc: pandora:/media/mmcblk0p3/dev/avrdude-5.6# opkg info bison Package: bison Version: 2.3-r5.0.5 Depends: libc6 Provides: Status: install user installed Section: devel Architecture: armv7a MD5Sum: c8e62fa82a96e9bba4c014c4345062ed Size: 181368 Filename: bison_2.3-r5.0.5_armv7a.ipk Description: GNU Project parser generator (yacc replacement). Installed-Time: 1283127122
 171 CoreFeature RequestMedium Update clock from hardware when restoring from low powe ...Closed
100%
Task Description The clock occasionally does weird things during low power mode, sometimes gaining time, sometimes losing. This is most likely a result of the CPU being reduced to 14Mhz and the system clock being unable to keep up. A convenient work around is to make a call to "/sbin/hwclock --hctosys" during wake-up to load the hardware clock back into the system clock. This may add an extra second or two to the wake-up time but will prevent confusion caused by clock being very incorrect.
 170 CoreBug ReportMedium Executable directories broken Closed
100%
Task Description Directory type packages fail to run. i.e. dropping a directory containing PXML.xml and a bunch of files onto the SD card rather than a .pnd package. The application is detected and menu entries created correctly, however pnd_run.sh fails to bind mount the directory due to bogus double quoting. Looks like a failed attempt to handle spaces in the path. Patch below removes these incorrect quotes. --- pnd_run.sh +++ pnd_run.sh.old @@ -161,2 +161,2 @@ elif [ $DFS = directory ]; then - mntline="sudo mount --bind -o ro ${PND} " + mntline="sudo mount --bind -o ro \"${PND}\" "
 169 CoreBug ReportLow pidgin freezes all the time Closed
100%
Task Description pidgin freezes all the time
 168 CoreBug ReportLow qt-embedded doesn't work Closed
100%
Task Description qt-embedded doesn't work
 167 ApplicationBug ReportLow midori crashes all the time Closed
100%
Task Description midori crashes all the time
 165 CoreBug ReportLow VPNC does't work Closed
100%
Task Description vpnc doesn't work
 164 CoreBug ReportLow Display brightness not restored at booting, HF4beta3 Closed
100%
Task Description The update from Hotfix3 to Hotfix4 beta3 broke restoring of display brightness at boot time. Restoring of brightness after "powersave mode" (aka flipping the power switch for a short time) does work nicely. This might be related to bug #163 ( http://bugs.openpandora.org/index.php?do=details&task_id=163 ) where shutting the display down via DPMS does result in the brightness being lost when getting the display on again. This is related to the desktop mode (XFCE). Don't know if it does happen for minimenu, too, not tested yet.
 163 Base OSBug ReportLow DPMS related "display problems" Closed
100%
Task Description Currently it looks like DPMS is active in xorg (eg when using XFCE). DPMS is normally used for stuff like turning the screen off to save energy. There seems to be no way to configure this while in XFCE. So the default xorg server values are used. At the moment the screen is turned off after 10mins of inactivity. Problems with this are a) that the time till it is turned off can not be configured b) after wakeup from such a DPMS related display shutdown the brightness is set to maximum. Solution to this: Deactivate the sleep values via xorg.conf. I am attaching a diff to "[openembedded.git] / recipes / xorg-xserver / xserver-xorg-conf / omap3-pandora / xorg.conf" changing those to "default off".
 162 CoreBug ReportMedium XFCE Setting date Closed
100%
Task Description The tool to setup the date/time in XFCE doesn't work properly : - Menu -> Settings -> Date and Time - The tool show up - Select the time zone Now an error window spam every seconds...
Showing tasks 101 - 150 of 311 Page 3 of 7 - 1 - 2 - 3 - 4 - 5 - Last >>

Available keyboard shortcuts

Tasklist

Task Details

Task Editing