|
55 | Core | Bug Report | Critical | .xinitrc problems (image from Feb 22nd) | Closed | |
Task Description
Loading a GUI from slim fails, as .xinitrc is broken.
Seems to have been edited using a windows editor? From line 50 on, there are newline characters that shouldn't be there.
Removing them makes XFCE4 loading fine. |
|
58 | Core | Bug Report | Critical | Pandora has not been shipped yet. | Closed | |
Task Description
Pandora has not been shipped yet. |
|
208 | Core | Bug Report | Critical | HOTFIX 4 and 5 Slow WIFI | Closed | |
Task Description
I'm getting 5kb/s with bursts up to 10kb/s if I am lucky.
I have attempted every channel on my router.
Tried every encryption even no encryption.
Tested with the router's wifi speed: 300Mbps 154Mbps and 45Mbps
I'm running Hotfix 5 RC2.
Wifi works fine with my android smartphone, and other wireless devices such as a laptop. |
|
237 | Core | Bug Report | Critical | /dev/mmcblkN - N sometimes points to left, sometimes to ... | Closed | |
Task Description
SPECIFICATION:
According to http://pandorawiki.org/SD_compatibility_list
/dev/mmcblk0 is the left SD card slot (the one being closer to the headphone check)
/dev/mmcblk1 is the right SD card slot
I trusted that device path specification.
And it was correct MOST of the time.
But sadly only most of the time, NOT ALWAYS!!!
This bug is severely dangerous, as a (possibly critical) command could unexpectedly affect a device other than the one you intended it for!
BUG INCIDENT:
Sadly, I realized this bug at the worst possible moment!
I issued the command: shred -fvz /dev/mmcblk0
but it erased the card in the RIGHT slot.
I realized that because the card inserted on the left has 16GB, and the one on the right 128MB.
I checked both the card positions and my entered command, to exclude my own mistake. Sadly it was not a clumsy mistake: This severe bug really exists!
BUG REPRODUCIBILITY:
I already slightly witnessed this bug during the last days, but thought it was just a coincidence.
I.e. in GParted the larger card showed up at the wrong device path.
I did a refresh and/or ejected/re-inserted the card, and the expected device path was back again, and I did not think further about this incident.
Only today with this fatal shred incident, I eventually realized this behavior is a bug.
Luckily I had my data backed up. |
|
2 | Core | Bug Report | High | pndnotifyd | Closed | |
Task Description
pndnotifyd needs to be restarted before it works (tested in image 2009-12-21)
This can manually be fixed by installing two packages:
http://www.angstrom-distribution.org/unstable/feed/armv7a/base/sessreg_1.0.4-r0.2_armv7a.ipk
http://djwillis.openpandora.org/pandora/packages/pandora-libpnd_1.0-r12.5_armv7a.ipk
And adding to lines to slim.conf:
sessionstart_cmd /usr/bin/sessreg -a -l $DISPLAY %user
sessionstop_cmd /usr/bin/sessreg -d -l $DISPLAY %user |
|
3 | Core | Bug Report | High | Permissions for brightness and CPU Speed | Closed | |
Task Description
/sys/devices/platform/twl4030-pwm0-bl/backlight/twl4030-pwm0-bl/brightness
/proc/pandora/cpu_mhz_max
Those values cannot be changed by the user, only by root.
Should be changed. |
|
5 | Core | Bug Report | High | Touchscreen Calibration stops the First-Boot-Wizard | Closed | |
Task Description
When selecting the touchscreen calibration within the first-boot-wizard, the script stops after the calibration and the Pandora continues to boot. |
|
8 | Core | Bug Report | High | WiFi doesn't work | Closed | |
Task Description
Error inserting /lib/modules/2.6.27-omap1/kernel/drivers/net/wireless/wl12xx/wl1251_sdio.ko: -1 Unknown symbol in module |
|
9 | Core | Bug Report | High | pmenu doesn't work | Closed | |
Task Description
Running pmenu leads to:
ERROR: config_read_file() failed: skins/Platinum/skin.cfg (line 21 of config skin.c)
(config_skin.c:22)
ERROR: cfg_gui_read failed, exiting... ( main.c:1517) |
|
10 | Core | Bug Report | High | Permissions / sudoers isse in 12-21 image | Closed | |
Task Description
pndnotifyd will create .desktop files
Running those will fail; if you've just done a recent sudo, they'll run fine
Probably sudoers file needs fix |
|
11 | Core | Bug Report | High | Console keymap: Two keys not mapped yet | Closed | |
Task Description
INS (Fn + Del) is not working in console yet.
ALT and CTRL are not working in console yet.
The rest of the console keys are fine (tested in nano).
Keys in X are mapped completely. |
|
28 | Core | Bug Report | High | pmenu only shows preview pictures when selecting the PN ... | Closed | |
Task Description
When selecting a PND for the first time, it only shows a red X.
When selecting the PND for the second time, it shows the preview picture. |
|
31 | Core | Bug Report | High | X11 Crashing with omapfb | Closed | |
Task Description
Cleaned up a bit.
* Mouse is inverted if you run SDL Games from the console.
* Mouse is not properly calibrated when you run SDL Games under X fullscreen. Fixed with notaz patch that also fixes the X11-Crash with omapfb (see below)
Regarding the X11-Crash when using SDL-Fullscreen-Apps together with omapfb:
notaz nailed down the problem: It's actually xf86-input-tslib's fault-
omapfb only acted as catalizator here, causing SDL to use different code path and call different X functions.
His patch also almost increases the touchscreen problem (see above): It runs perfect for games in 800x480.
However, on small issue is left on apps with lower resolution which use their own mouse cursor:
As soon as you move the mouse outside of the game resolution (i.e. SuperTux runs 640x480), the mouse cursor stops at the end of the virtual screen and you have an offset.
This only seems to happen when the game uses it's own mouse cursor. If you go to the level editor of SuperTux and leave, the normal X cursor appears and the problem doesn't occur anymore.
So this is probably something that needs to be fixed in the game, not in the driver.
A compiled version (for testing):
http://notaz.gp2x.de/tmp/tslib_drv.so --- needs to be copied here: /usr/lib/xorg/modules/input/tslib_drv.so |
|
38 | Core | Bug Report | High | ALSA crashes every so often | Closed | |
Task Description
EDIT: Doesn't seem to be crashing. Looks like the amp hasn't been setup properly.
There is a fix by notaz:
http://notaz.gp2x.de/tmp/uImage
Use that with the latest image (Feb 13th) to test it out.
ALSA crashes pretty often. Not sure, but I think it does this when something is eating up a lot of CPU.
ALSA starts to spit out buffer_underrun errors and occasionally crashes with an input/output error.
Then no sound will come from an SDL app.
You can reinitialize it by playing a song with XMMS. |
|
39 | Core | Bug Report | High | file doesn't work (missing magic files) in image from F ... | Closed | |
Task Description
It seems there's a bug in the latest package "file 5.04-r0.5" of the Angström repository:
It's missing the magic files and therefore doesn't work.
Unfortunately, pnd_run.sh depends on it and therefore it breaks the PND-system.
Installing an older stable version (http://www.angstrom-distribution.org/feeds/2008/ipk/glibc/armv7a/base/file_4.21-r0.1_armv7a.ipk) does make it work again.
First appeared on image from Feb 13th, not fixed in image from Feb 22nd yet. |
|
54 | Core | Feature Request | High | Make it possible to enable / disable keyboard mappings ... | Closed | |
Task Description
Some stuff (UAE4ALL, SuperTux, etc.) is having problems because ABXY and DPAD are mapped to keyboard buttons.
I guess this will lead to more problems in the near future with SDL apps, so it should be configurable to enable / disable the keyboard -> DPAD / ABXY mappings.
Maybe this could be included into libpnd? |
|
57 | Core | Bug Report | High | New GLES driver not working yet (image from Feb 22nd) | Closed | |
Task Description
New GLES driver doesn't seem to load correctly right now.
Therefore, pmenu is also not working in this image. |
|
66 | Core | Bug Report | High | libpnd : pnd_pnd_mount() function bug | Closed | |
Task Description
libpnd : pnd_pnd_mount() function do not seems to wait the mount to success before returning, this can cause some application to try to access the pnd content before it really get mounted. |
|
69 | Core | Bug Report | High | libpnd : pnd_apps_exec() function bug | Closed | |
Task Description
PND_EXEC_OPTION_BLOCK do not seems to work anymore ( the function does not wait the pnd_run.sh task to finish anymore ) |
|
76 | Core | Bug Report | High | Wifi connection lost under high CPU load | Closed | |
Task Description
I noticed that when I tried Quake 3 a while back that I would lose my internet connection. Only the very first time I tried it did it ever find a couple thousand servers and let me join a map. Since then, it always dies and I never see any servers.
I wasn't too concerned yet because maybe it's just Q3 doing something but tonight mplayer was running full screen and then suddenly it started chugging and the network manager popped up that it was trying to connect (spinning logo at the bottom). Since you only get one shot at network manager per boot, it was a lost cause.
The correlation I make here was that I'm sure the CPU was under heavy load for both cases but I haven't tried other programs to see what happens. I didn't have any games on this card tonight. Can anyone repeat this problem or is it a known issue? |
|
81 | Core | Bug Report | High | pandora seems to hang during boot, turns out it didn't | Closed | |
Task Description
it seemed just now thay my pandora didnt complete its bootsequence. During booting, the screen turned black. I thought it had crashed, but I still saw lights flashing when I inserted an SDcard.
I then assumed that it WAS booting normally, but that the screen was turned down. So I pushed enter to confirm my username, as I suspected that I was at that prompt. Next I inputted my pwd, pushed enter, waited a bit, and then ised Fn+I to increase the brightness. It worked!
I think that during the bootprocess the screen should at most be set to the darkest setting, but never to off.
I think I know what happened. I told my pandora to shutdown and closed the lit before it was done. I guess that that swiittched off the screen, a setting which was then saved by the shutdown process, and restored during the bootsequence.
I would suggest fixing this in the startup process, rather than the shutdown process, because that way, no matter what ends up in the settings, a sensible valsue is set at startup. I'll see if I can reproduce this. |
|
101 | Core | Bug Report | High | Cannot unmount SD card or USB stick through the GUI | Closed | |
Task Description
When I rightclick and select "unmount" I always get an error, see below.
unmounting from a terminal window works fine.
Also see:
http://www.gp32x.com/board/index.php?/topic/54353-unmount-sd-card-hdd/
"Unable to unmount .... Cannot open /media/.hal-mtab" |
|
136 | Core | Bug Report | High | rather high battery discharge while Pandora is powered ... | Closed | |
Task Description
The Pandora does seem to use too much energy while it is turned off. A testcase: The pandora was turned off over night (about 8 hours) and battery state dropped from 98% to 96%. When removing the battery from the pandora for the same amount of time, the state is not changed at all.
This is based on the zaxxon firmware release with hotfix3, beta2.
Problem: if you don't use the pandora for a while and forget to remove the battery you can cause a deep discharge which might damage the battery. This is also a problem if the Pandora does eg shutdown itself since power is out and you can't directly attach it to a charger.
Possible causes:
* Design fault in the board.
* Too much powered on while the device *should* be completely powered off. The only things that should get power are the clock and the power button. This should basically not drain much.
Regarding the clock: The PalmPre is based on the OMAP3, too. There you basically have no discharge when it is powered off, so it is unlikely that the fault is in the OMAP3 itself. |
|
140 | Core | Bug Report | High | WiFi Starts off fast then slows down | Closed | |
Task Description
When downloading files using a browser or wget or when attempting to stream videos we see a fast initial burst which then slows down dramatically.
see following topics for more details and actual user stats.
http://www.gp32x.com/board/index.php?/topic/54340-post-your-speed-over-wifi/
http://www.gp32x.com/board/index.php?/topic/54921-you-tube-through-vlc/
http://www.gp32x.com/board/index.php?/topic/54831-minitube/
http://www.gp32x.com/board/index.php?/topic/54901-possible-wifi-issues/ |
|
152 | Core | Bug Report | High | Data transfer issued between SD slot 1 and 2 | Closed | |
Task Description
It appears that any users are having trouble transferring files from SD cards in slot 1 to SD cards in Slot 2.
Full details here.
http://www.gp32x.com/board/index.php?/topic/55077-looks-like-the-is-a-readtiming-problem-with-sd-reading-when-high-cpu/ |
|
154 | Core | Bug Report | High | Vpn doesn't work | Closed | |
Task Description
When clicking on the Network Manager Applet Symbol, then selecting "VPN Connections" and then "Configure VPN", all the buttons in the following dialoge are greyed out. There is no way to add a new vpn connection. Restarting the system or deactivating the WiFi and then reactivaing it doesn't help. |
|
173 | Core | Bug Report | High | X uses 100% cpu in low power mode | Closed | |
Task Description
After 10 minutes in low power mode X seems to go nuts and use 100% CPU. Obviously this is bad ;-) 14MHz isn't *that* slow, so there's obviously something getting wedged.
I haven't been able to figure out exactly what's happening, but the fact that it always occurs after exactly 10 minutes suggests its power management related. Maybe we're getting stuck trying to kick off the screensaver, or something?
Hacking op_power.sh do disable screen blanking shows that, unsurprisingly, the screen freezes at the same time X goes AWOL.
Pressing the power switch brings the device out of low power mode, though there is often a few seconds additional delay as the event handling scripts take longer than normal to run because the CPU is already busy.
I've attached the results of
top -b -d 60 > toplog &
while sleep 60 ; do cat /proc/loadavg; done > loadlog |
|
183 | Core | Bug Report | High | Left mouse click and hold = fail | Closed | |
Task Description
When I want to hold and select multiple files its not working. Not with the nubs or the touchscreen.
I can try an easy test by making the select rectangle on the desktop. It only becomes very very tiny. If I try very fast diagonal drag motion on the touchscreen. It becomes a little larger.
Trying to grab scrollbar is the same issue. |
|
187 | Core | Bug Report | High | LCD turns off after "rdate" updated the date | Closed | |
Task Description
running "sudo rdate -s time.ien.it" will set the brightness of the LCD to 0.
User has to use FN + I to increase it back to a usable level.
"rdate" asks for the super-user password as expected, updates the date as expected, but turns off the screen. |
|
188 | Core | Bug Report | High | "rdate" sets the time exactly 3 hours in advance | Closed | |
Task Description
"rdate -s time.ien.it" will set the date (hour) 3 hours in advance.
The time (and timezone) can be adjusted manually using the "Settings -> Date and Time" tool, but on the next rdate-update the issue will occur again |
|
195 | Core | Feature Request | High | Start re-recharge of battery sooner | Closed | |
Task Description
Increase battery LVL_4 and LVL_3 threshold.
After reaching 100%, in some cases the charge circuit enters "battery full" state, stops charging, and begins to discharge. This is not entirely unexpected behavior according to the spec sheet, although I don't fully understand exactly the situations in which it completes charging. Once the battery is full, the battery will begin discharging. The charge circuit automatically restarts the recharge once the voltage has gone below a certain level (crosses below the LVL_3 voltage threshold)
The default LVL_3 voltage threshold is 3.902 volts which is at about 80-85% battery level as recorded by bq27500 chip. In my opinion, this is way too low.
Setting the BCIMFTH2 register to 0xCB increases the voltage threshold to about 4.003 volts which is about 93%.
Setting it to 0xDC may also be worthwhile, which is just over 95%.
By default, if a user leaves their Pandora plugged in overnight, they may wake up to find their Pandora has stopped charging and the capacity has dropped to almost 80%, which can be quite startling to some users who will then report it as a bug.
This change will ensure that it never drops below 93-95%, a much more acceptable level.
Specific code changes suggested, in the /drivers/power/twl4030_bci_battery.c file, somewhere in the twl4030_bci_battery_probe function (or a function called by it), add the lines:
/********************************/
#define KEY_FTH2 0x7F
#define REG_BCIMFTH2 0x017
ret = twl4030_i2c_write_u8(TWL4030_MODULE_MAIN_CHARGE, KEY_FTH2, REG_BCIMFKEY);
if (ret)
return ret;
ret = twl4030_i2c_write_u8(TWL4030_MODULE_MAIN_CHARGE, 0xDC, REG_BCIMFTH2);
if (ret)
return ret;
/********************************/
(Move defines to the top, as appropriate) |
|
197 | Core | Bug Report | High | [PATCH] Fix opp if booting with wrong settings in hw | Closed | |
Task Description
Hi,
This should help with cases like this
http://www.gp32x.com/board/index.php?/topic/57303-overclocking-broke-my-pandora/
Patch attached. |
|
201 | Core | Bug Report | High | PND apps still use memory after they've quit | Closed | |
Task Description
After running and quitting a PND app, not all of the used memory is being freed.
This eats more and more memory over time. Just run 5 or 6 apps and you only have half of the memory left.
Sounds like either aufs or unionfs don't free the memory after unmounting.
This has been reported with HF4 and still is the case with HF5 Beta 2
-- downgraded to 'Researching' and 'Normal' priority until confirmed and details found |
|
214 | Core | Bug Report | High | op_wifi pnd not exiting cleanly, with fix (one characte ... | Closed | |
Task Description
The op_wifi pnd does not exit out cleanly once the encased script executes,
the pndrun_op_wifi.out reports
umount: /mnt/utmp/op_wifi: device is busy.
umount: /mnt/utmp/op_wifi: device is busy.
umount UNION failed, didn't clean up. Process still using this FS :
3197 ? S 0:00 /bin/sh /etc/init.d/wl1251-init start
This op_wifi.sh just calls
/usr/pandora/scripts/op_wifi.sh
for some reason, the init.d/w.... start causes it to hang, I executed all this locally, and it doesn't appear to keep running
Appending " &" to the line which calls this init script, solves the problem. |
|
223 | Core | Bug Report | High | op_power.sh kills gles context | Unconfirmed | |
Task Description
opengles and op_power.sh don't like each other very much.
whenever returning from low power to full power mode again, opengles rendering is just dead.
the reason for this issue are following 2 lines within op_power.sh
18 echo 0 > /sys/devices/platform/omapfb/graphics/fb0/blank
...
66 echo 1 > /sys/devices/platform/omapfb/graphics/fb0/blank
if these lines are removed/commented, the gles rendering just resumes fine. |
|
226 | Core | Feature Request | High | Boot from /dev/sda devices requested | Closed | |
Task Description
Boot from usb hard disk not supported. This should be a rather simple fix of adding the sdx devices and adjust the boot scripts??
I was able to put this autoboot.txt on mmc 0:1
setenv bootargs debug root=/dev/sda1 rw rootdelay=2 console=ttyS0,115200n8 vram=6272K omapfb.vram=0:3000K
ext2load sda 0:1 0x80300000 /boot/uImage
bootm 0x80300000
This failed with amongst other things "Block device sda 0 not supported" and something about failing to load kernel
So I then changed the autoboot file to this
setenv bootargs debug root=/dev/sda1 rw rootdelay=2 console=ttyS0,115200n8 vram=6272K omapfb.vram=0:3000K
ext2load mmc 0:3 0x80300000 /boot/uImage
bootm 0x80300000
All this did was die after the kernel loaded.
I believe I could much better make use of this device if I could boot from some faster storage, please advise :) |
|
229 | Core | Bug Report | High | Enable wake on alarm interrupts | Unconfirmed | |
Task Description
Found I'd kept some notes about making the Pandora's wake on alarm function work...
drivers/rtc/rtc-twl4030.c
twl4030_rtc_remove (for when the driver is removed) and twl4030_rtc_
shutdown (for when the system is shutdown) functions need to change. Or at least the shut down does.
oh YUK who's been using goto....
changes in drivers/rtc/rtc-twl4030.c
twl4030_rtc_remove
commented out //mask_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_ALARM_M);
twl4030_rtc_shutdown
replaced
// mask_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_TIMER_M |
// BIT_RTC_INTERRUPTS_REG_IT_ALARM_M);
with
mask_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_TIMER_M);
twl4030_rtc_suspend
replaced
// mask_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_TIMER_M |
// BIT_RTC_INTERRUPTS_REG_IT_ALARM_M);
with
mask_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_TIMER_M);
twl4030_rtc_init
added (before return!)
twl4030_rtc_alarm_irq_set_state(true);
Should probably check reg 0x2B with mask 0x08 to see if alarm should be left enabled or not ?
but only in twl4030_rtc_shutdown and ?remove? NOT in twl4030_rtc_init
should remove ever happen ???
I'm guessing it's best to not enable the alarm irq's all the time??? |
|
254 | Core | Bug Report | High | Several apps leave graphical artefact overlay (ghost) a ... | Closed | |
Task Description
After quitting some apps, their last graphical output remains on the screen, which covers a large area of the Pandora, and therefore makes it quite unusable, so that only a full restart resolves this issue.
As this happens in many apps (Mednafen-GB, Dark Light Battles, etc) this must be a problem within a shared library (driver, graphics lib, window manager framework, or similar). |
|
259 | Core | Bug Report | High | Hold switch does NOT lock keyboard! Especially crucial ... | Closed | |
Task Description
Apps, which operate with the Pandora in closed lid mode, such as audio players, server processes, etc, in a button-press-probably environment (as i.e. your pocket) still CAN receive the shoulder button L + R key presses, and if they have a meaning in these programs, they could trigger undesired actions.
And also in the current implementation of the Low Power Mode (See: FS#260) key presses may still be received.
Therefore I strongly propose to implement the HOLD switch to en/dis-able a keyboard lock.
IN DETAIL: This shall be global, meaning that the input processing software (however this is implemented on the Pandora: kernel, driver, … ) keeps the lock state (on/off), and if the keyboard state is off,
a) discards all input, or
b) if it makes sense for some reason/applications (any ideas?) just writes them into a queue/buffer, which gets (partially) executed or made accessible to certain software after the keyboard gets unlocked again.
FYI: I have tested the hold switch with the Pandora Input-Tester, and it is recognized. So my report is definitely a software (and not an hardware) issue. |
|
261 | Core | To Do (Reminder) | High | Overview of all current KEYBOARD INPUT related issues | Unconfirmed | |
Task Description
Built-in keyboard input is a central thing on the Pandora, as it concerns almost all user interfaced apps!
I realized that I myself and also others submitted quite many reports concerning this issue.
Hence this meta issue is intended as an overview/accumulation/aid for those devs who are willing to overwork the whole issue.
If you realize new related issues, feel free to add them here.
If this my effort is contradicting the OpenPandora workflow, then pardon me, and instruct me, how else to handle issues of that kind. Thanks!
Keyboard low level: Driver, keyboard layout, post processing (hotkeys, input support, etc)
FS#138 FS#227 FS#242 FS#259
Keyboard mid level: Application interfacing
FS#102 FS#123 FS#238
Keyboard application internal level
FS#157 (dupe: FS#249 ) FS#243 FS#256 |
|
267 | Core | Bug Report | High | HF6-Updater.pnd loses pnd_run.sh | Closed | |
Task Description
Several users have reported that running HF6-Updater.pnd leads to a missing /usr/pandora/scripts/pnd_run.sh
Possibly the file is locked by the Updater itself when installing pandora-libpnd_1.0-r56.5_armv7a.ipk
Forum thread:
http://boards.openpandora.org/index.php?/topic/5652-hotfix-6-final-released/page__view__findpost__p__99313 |
|
6 | Core | Bug Report | Medium | Calibrate Touchscreen within the Settings-Menu of XFCE ... | Closed | |
Task Description
It doesn't run. |
|
15 | Core | Bug Report | Medium | Permissions / automounted SD Card | Closed | |
Task Description
Only root has write access to automounted SD Cards. The normal user can only read. |
|
16 | Core | Bug Report | Medium | normal user login fails over serial/ttys | Closed | |
Task Description
Only root can login over serial or ttys, and only if it has no password. Ssh login works fine.
After some debugging it seems to be PAM issue, possibly recipes/shadow/ misconfiguration in OE. Maybe we sould use IMAGE_LOGIN_MANAGER = "busybox" instead of IMAGE_LOGIN_MANAGER = "shadow" as we don't need super security? |
|
18 | Core | Bug Report | Medium | Some errors in first-run-wizard.sh | Closed | |
Task Description
Line 154 and 157 need to be changed:
153 if [ $launcher == "xfce" ]; then
154 sed -i 's/.*sessions.*/sessions xfce4,pmenu/g' /etc/slim.conf
155 echo Xfce selected as default interface
156 else
157 sed -i 's/.*sessions.*/sessions pmenu,xfce4/g' /etc/slim.conf
158 echo PMenu selected as default interface
159 fi
They should be:
154 sed -i 's/.*sessions .*/sessions xfce4/g' /etc/slim.conf
157 sed -i 's/.*sessions .*/sessions pmenu/g' /etc/slim.conf
Note the empty space behind sessions. :) |
|
25 | Core | Bug Report | Medium | QWERTY Slowdowns | Closed | |
Task Description
Cleaned up a bit according to everything we know.
EDIT: notaz did it again. Fixed it. If you find any weird side effects, let us know :)
http://notaz.gp2x.de/tmp/Xorg
Replace the file /usr/bin/Xorg
Be sure to change permissions to 755
Switching between DPAD and keyboard does increase CPU usage on X A LOT. It even tends to crash ALSA if done too extensive.
According to notaz, this is due to some very old crap that's still included in X.
Internally it has one mouse and one keyboard, everything else is copied every time you press a key and bunch of callbacks are called, messages are sent to all screens and windows.
New tests from EvilDragon:
Disabling xfwm4 makes things better (ALSA won't crash anymore), but it still lags. Running it in minimal X (directly from .xinitrc) strangely fixes this - X won't eat up more than 17% CPU,
regardless how many buttons you press.
OLD Entry:
The qwerty controls when pressed are causing the system to slowdown making the application running to pause/delay. Ive seen in a least 2 application glquake and supertux. For example pressing space would cause the hiccups and shortly after the pressing stopped the application would regain normal running speed. The other joystick/nub controls work fine. glquake is getting controls direct from the event files. Supertux is using the SDL layer.
This was done on angstrom image from dec 19th.
EDIT: More tests done by EvilDragon with the latest image (pandora-xfce-image-omap3-pandora-20100102-new-kernel-fn-n-m-support.tar.bz2)
When you play with the DPAD and press a keyboard button, the app is making the small pause. You can press as many keyboard buttons as you want after that, there won't be another pause.
BUT as soon as you press the DPAD again, it pauses again. Then the next pause does happen when you press a keyboard button, etc.
So it feels like it pauses when you switch between DPAD and keyboard.
The most important thing: This only happens when you run SDL Games from X. It doesn't occur when running SDL games from the console. |
|
26 | Core | Bug Report | Medium | pndevmapperd only works when manually started | Closed | |
Task Description
Though pndevmapperd runs after booting (ps -A lists it), it doesn't react to anything.
EDIT: It DOES do something. It creates defunct op_menu.sh with each press.
When you run it manually from the terminal, the menu button works find and shows the appfinder. |
|
30 | Core | Bug Report | Medium | New issues in current image (pandora-20100102-new-kerne ... | Closed | |
Task Description
* It takes forever to startup.
It hangs while trying to initialize the new SDIO-WiFi:
[ 2363.922271] wl1251: WARNING WLAN not ready
[ 2363.927581] wl1251_sdio mmc2:0001:1: firmware: requesting wl1251-fw.bin
[ 2423.930328] wl1251: ERROR could not get firmware: -2
[ 2424.033447] wl1251: ERROR sdio write failed (-110)
[ 2425.786071] wl1251: ERROR sdio read failed (-110)
[ 2425.790893] wl1251: WARNING WLAN not ready
[ 2425.795776] wl1251_sdio mmc2:0001:1: firmware: requesting wl1251-fw.bin
* OpenPandora Start-Button is too small (has the same width as a normal icon) |
|
43 | Core | Bug Report | Medium | libpng missing from the last images (since approx mid o ... | Closed | |
Task Description
Some ports (like SMW, VICE, etc.) stopped working because libpng is missing from the current images.
Installing it does fix that problem.
http://www.angstrom-distribution.org/unstable/feed/armv7a/base/libpng_1.2.42-r2.0.5_armv7a.ipk |
|
44 | Core | Bug Report | Medium | Pandora-Start-Menu button too small | Closed | |
Task Description
Since about mid January, the Openpandora-Startmenu-Button doesn't resize when the "Show Title" is enabled.
Therefore, you only see parts of the "OpenPandora"-Title and no icon.
Disabling the title shows the icon. I have no idea how to resize it and why this happened (the theme hasn't been changed as far as I know) |
