|
94 | OpenPandora Main OS | Core | Bug Report | Low | Backlight control by lid sensor not detected after boot | New | |
All |
Task Description
If you boot the system with the lid closed, the backlight will still be on when you get to the desktop. You have to lift the lid for an instant and then close again to shut it off. Perhaps this is because of the lack of trigger for an interrupt since the sensor is already activated. Can there be one extra check of the lid sensor after boot to cover this static position? |
|
110 | OpenPandora Main OS | Core | Bug Report | Very Low | Battery percentage static in MiniMenu | Unconfirmed | |
All |
Task Description
Battery remaining percentage in MiniMenu does not update unless you change tabs back and forth.
This is only really an issue when leaving the unit charging and not using it. It gives the appearance that it is not charging until you swap tabs around. |
|
138 | OpenPandora Main OS | Core | Bug Report | Low | 'del' key (shift+backspace) not working | New | |
All |
Task Description
The title says everything: The 'del' key does not work. In theory you should have a del "event" when hitting shift+backspace. This is not the case in all progs I tested so far (terminal and default text editor with gui). |
|
148 | OpenPandora Main OS | Core | Bug Report | Low | add standard library path to ldconfig.so.conf to help l... | Unconfirmed | |
All |
Task Description
cat >/etc/ld.so.conf |
|
155 | OpenPandora Main OS | Core | Bug Report | Medium | Critical problems after rescaling GLES2 X windows | Unconfirmed | |
All |
Task Description
When a X window which is displaying GLES2 render output is:
- Either dragged out of the visibile screen region (?)
- Is made larger than it was at the creation time of the GLES2 context
then:
- The performance will drop significantly as the EGL buffer swaps won't occur as fast as before,
- The render output will be corrupted and flicker
- In rare occasions crashes the application or locks up the entire system (which forces you to remove the battery)
The problem can not be solved without restarting the application (Possibly forcing players to complete the same goals again as they were unable to reach a savepoint or similar things).
This was confirmed in Mupen64Plus and the PowerVR GLES Samples and some of my own projects (which are, however, based on the PowerVR samples).
As I didn't see any other reports about this problems (but had it confirmed by other Pandora users too) I would expect that it can be fixed by using a newer X, kernel or combination of them as other OMAP users would be effected too. |
|
178 | OpenPandora Main OS | Core | Bug Report | Low | Mount-loop when booting from SD-card | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
When booting the pandora-OS from sd-card by using the official tar, you will end up with your sd-card being mounted twice: once as / and once as /media/. I solved this by adding "/dev/mmcblk0" to "/etc/udev/mount.blacklist". Maybe this should be added to the default tarball? I'm not sure as it might be used in other ways maybe (beside SD-card-installation)?
Background: I ran "updatedb" as root and have been notified by a message that there was a mount-loop. After adding the above modification the system still booted fine and "updatedb" ran nicely without a warning. |
|
179 | OpenPandora Main OS | Core | Bug Report | Low | .vimrc-preset for user but not for root | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
I am running PandoraOS from sd-card installed with the official tarball "pandora-rootfs.tar.bz2".
I noticed that the control/keyboard-mapping in vi does not work correctly after switching to root (for example sudo su-). I solved this by copying over my users .vimrc to root-homedir. This should already be included in the tarball. |
|
185 | OpenPandora Main OS | Core | Bug Report | Low | Xorg driver should not be dependant on user environment | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
The patch implementing screen blanking uses the /usr/pandora/scripts/op_lid.sh script to control LCD backlit:
http://git.openpandora.org/cgi-bin/gitweb.cgi?p=openembedded.git;a=blob;f=recipes/xorg-driver/xf86-video-omapfb/pandora_backlight_dim.patch;h=4a0b8432d083c6e7297192a2920c7a777ae3d098;hb=16f3fff44323bd6b4349d909667b51a2fef3f278
The same result can be achieved by using the sys interface:
/sys/devices/platform/twl4030-pwm0-bl/backlight/twl4030-pwm0-bl/bl_power
This approach makes driver independent on particular distribution. The proposed patch is attached. |
|
190 | OpenPandora Main OS | Core | Bug Report | Medium | Removing desktop-shortkeys does not work | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
Try clearing shortcuts in Start->Settings->Window Manager->Keyboard. That doesn't work (for me).
This is a problem because these shortcuts are blocking key-combination in apps, like for example the keymapper in dosbox (CTRL+F1) or refreshing content (CTRL+F5). I tried manual editing or even deleting the configuration file, but changes are not recognized and the file recreated on reboot. |
|
191 | OpenPandora Development OS | Core | Bug Report | Low | Add XInput extention to allow pressure sensivity in app... | Unconfirmed | |
Release 2 (.next) |
Task Description
Please see this for GTK apps : http://library.gnome.org/devel/gdk/stable/gdk-Input-Devices.html
And see this thread : http://boards.openpandora.org/index.php?/topic/372-xournal-pdf-annotations/page__gopid__6836#entry6836 |
|
204 | OpenPandora Main OS | Core | Bug Report | Medium | fonts issues | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
Ok, I just want to say that there is something missing about the font on the base image. I cant get what (at least for now)
Here is an issue : http://www.gp32x.com/board/index.php?/topic/54282-getting-vnc-viewer-to-work/
With my current Ogre build I get :
Warning: Unable to load any usable ISO8859 font
Error: Aborting: no font found
I've googled but so far no solution :( |
|
223 | OpenPandora Main OS | Core | Bug Report | High | op_power.sh kills gles context | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
opengles and op_power.sh don't like each other very much.
whenever returning from low power to full power mode again, opengles rendering is just dead.
the reason for this issue are following 2 lines within op_power.sh
18 echo 0 > /sys/devices/platform/omapfb/graphics/fb0/blank
...
66 echo 1 > /sys/devices/platform/omapfb/graphics/fb0/blank
if these lines are removed/commented, the gles rendering just resumes fine. |
|
225 | OpenPandora Main OS | Core | Bug Report | Medium | ads7846 reports odd pressure values | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
using evdev xorg drivers and not the tslib drivers you can receive pressure axis data however there is
a problem with the values reported by the ads7846 module and the evdev driver has no calibration property for pressure
using
xinput test touchscreen
you can see the pressure axis ranging from 120-ish for hard press to about 150-170 for light press (low pressure values can
be quite erratic)
I could possibly hack the evdev module to possibly do something with this odd and narrow range of values, but I rather think looking
at the source that the ads7846 module needs some work.
is there a git tag that has a known working configuration? as I've had problems getting the kernel to compile the last few times I attempted... |
|
227 | OpenPandora Main OS | Core | Bug Report | Low | Delete button won't delete, and function lock doesn't w... | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
If you hit the function button, then hit it again to lock the function keys, it doesn't lock the function key.
The delete key, hold shift and hit the back space button, it won't delete, meaning it won't remove the character to the right of the cursor. I saw this on the forum, and confirmed it on my pandora also. |
|
229 | OpenPandora Main OS | Core | Bug Report | High | Enable wake on alarm interrupts | Unconfirmed | |
All |
Task Description
Found I'd kept some notes about making the Pandora's wake on alarm function work...
drivers/rtc/rtc-twl4030.c
twl4030_rtc_remove (for when the driver is removed) and twl4030_rtc_
shutdown (for when the system is shutdown) functions need to change. Or at least the shut down does.
oh YUK who's been using goto....
changes in drivers/rtc/rtc-twl4030.c
twl4030_rtc_remove
commented out //mask_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_ALARM_M);
twl4030_rtc_shutdown
replaced
// mask_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_TIMER_M |
// BIT_RTC_INTERRUPTS_REG_IT_ALARM_M);
with
mask_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_TIMER_M);
twl4030_rtc_suspend
replaced
// mask_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_TIMER_M |
// BIT_RTC_INTERRUPTS_REG_IT_ALARM_M);
with
mask_rtc_irq_bit(BIT_RTC_INTERRUPTS_REG_IT_TIMER_M);
twl4030_rtc_init
added (before return!)
twl4030_rtc_alarm_irq_set_state(true);
Should probably check reg 0x2B with mask 0x08 to see if alarm should be left enabled or not ?
but only in twl4030_rtc_shutdown and ?remove? NOT in twl4030_rtc_init
should remove ever happen ???
I'm guessing it's best to not enable the alarm irq's all the time??? |
|
236 | OpenPandora Main OS | Core | Bug Report | Low | Cannot unmount SD-Card | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
SD-Card in Pandora can only be unmounted by guest (uid=1000) but not by jgeiss (uid=1001).
Steps To Reproduce:
Insert SD-Card (or boot with SD-Card inserted),
Login as jgeiss (uid=1001),
Try to unmount SD-Card via XFCE-Popup-Menu (right mouse click on SD-Card-Icon and select unmount). |
|
257 | OpenPandora Main OS | Core | Bug Report | Medium | TV Out script breaks XV/SDL Video playback | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
This seems to be the case with Hot-fix 5 and 6 alpha 4.
I've been able to repeat this bug by re-flashing..
On a fresh re-flash.. installed community codec pack.. Videos will play fine on Panplayer, VLC and Gnome-Mplayer with default settings, which I believe is XV or SDL out in the case of VLC.
Run the TV-out script it will cause a blank black screen during playback.. Disabling TV-out, switching modes, rebooting.. battery out, nothing seems to allows it to work with XV/SDL out again.. I know If I switch to X11 it will make it "work" again, but I notice a bit of lag during playback using X11 compared to XV/SDL out. |
|
260 | OpenPandora Main OS | Core | Bug Report | Medium | Low Power Mode: Input (keyboard, nub) still taken. Appl... | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
This is the related documentation:
http://pandorawiki.org/Power_modes#Low_Power
(Please update accordingly as part of the issue resolution)
FROM MY USER EXPERIENCE:
If you put the Pandora into Low Power Mode, then press some keys, and then wake the Pandora back into Normal Mode, your input (both keys and nubs, haven't tried with USB input yet) seem to have triggered something while the device was in Low Power Mode!
What does really happen in Low Power Mode concerning execution and input?
a) Input is received AND triggers as application execution continues
or
b) Kernel/driver queues the input signals into a buffer, and executes them on wake?
If supposition a) or b) is true, then this would be one more reason to properly implement: FS#259
OBSERVANCE EXAMPLE 1:
1) Start MiniMenu. Mentally note down your active tab.
2) Put Pandora to Low Power Mode.
3) Press shoulder button R once.
4) Wake Pandora to Normal Mode. You are now one tab to the right of where you left. Input must have been caught in Low Power Mode, but wether execution of it happened while Low Power Mode or later after wake in Normal power Mode is unclear.
OBSERVANCE EXAMPLE 2:
1) Start gedit (a text editor). Insert the digit "1".
2) Put Pandora to Low Power Mode.
3) Press: CTRL-N 2 CTRL-N 3 CTRL-N 4. (Without the spaces)
4) Wake Pandora to Normal Mode.
5) For a fraction of a second you see the tabs building up. Either the input was really received AND executed while Low Power Mode and what you see is just a delayed window manager refreshment, or the input was queued in Low Power Mode, and only executed on wake. |
|
269 | OpenPandora Main OS | Core | Bug Report | Low | Thunar Slow Exit | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
Thunar takes a long time going back to minimenu on exit. You don't notice this when in XFCE but then you are always in the GUI not returning to it.
This started in Hotfix 6 Alpha4 I believe |
|
270 | OpenPandora Main OS | Core | Bug Report | Very Low | Power-slider & lid-close events: XFCE observes user set... | New | |
Release 1 (Zaxxon) |
Task Description
STATUS QUO:
If you are in XFCE and hold the power slider for 3 seconds, you thereby trigger the shutdown command.
For 3 more seconds a dialogue box gives you the chance to abort the shutdown ("Shutting down in 3…2…").
Now in MiniMenu no direct shutdown key is available. You first have to quit the running app (via PANDORA key), then call up the menu (via SELECT key), and then navigate to "Shutdown" and confirm it (by B or ENTER).
INQUIRED BEHAVIOR:
1) Thanks to the very recent MiniMenu speedups, these 4 consecutive user interaction steps can now at least be be executed a lot faster.
Nevertheless, offering a 1-button-interaction (via power slider) too, would be nice. Could you please make that available to MiniMenu?
And in general: Make this power-slide-event available to any possible GUI, so that not each GUI has to implement this by itself, but rather the OS catches this event and handles it uniformly, except if a certain GUI WANTS to establish an exception to the rule.
2) Also the "Lid-Close-Settings" seem to be ignored by MiniMenu. MiniMenu seems to have the action "Turn off screen" hardcoded to that event. Please make MiniMenu observe the user settings from "Lid-Close-Settings".
RELATED SOURCE CODE FILES (to my knowledge):
op_lid.sh
op_power.sh
op_bright_up.sh
op_bright_down.sh |
|
290 | OpenPandora Main OS | Core | Bug Report | Medium | gnome-mount not available | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
In GTK applications, such as Truecrypt, NoteCase Pro or Mousepad, the file open / file save dialogs have shortcuts to mounted file systems on the left side.
If clicking such a shortcut entry, the corresponding file system's contents are shown in the right dialog pane.
This works for file systems, which were available at boot time.
For file systems mounted after booting, e.g. by inserting an SD card or connecting a USB drive, when clicking such an entry, an error message appears saying
"Could not mount [volumen name]
Failed to execute child process 'gnome-mount' (No such file or directory)"
This is healed by
sudo opkg install gnome-mount
(which instals gnome-mount, nautilus, gvfsd-ftp, gvfs (upgrade), and a lot of libs (upgrades)..
This has been seen in SuperZaxxon release 1.5, not in Beta3 (but Beta3 is the only choice in Flyspray's dropdown currently).
I reported that error for HF6 I think, and it seemed to be fixed in SuperZaxxon Beta5. A regression? |
|
291 | OpenPandora Main OS | Core | Bug Report | Medium | root-owned pndrun_...out file makes PND refuse starting | Assigned | |
Release 1 (Zaxxon) |
Task Description
If a PND has been run as root before (using pnd_run.sh from a root shell) and afterwards it is invoked the normal way, the PND doesn't start, because the .out file cannt be overwritten:
/usr/pandora/scripts/pnd_run.sh: line 26: /tmp/pndrun_firefox.out: Permission denied
Desired solution:
.out file is silently overwitten.
Maybe, if that's not possible, create another .out file with a different name (added counter, for example).
Seen in SuperZaxxon relese 1.5, not in Beta3 as this task is flagged, but there is no choice besides Beta3. |
|
292 | OpenPandora Main OS | Core | Bug Report | Low | Can't seek in ogg files using pygame / SDL | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
Using pygame I try to play a music file starting from some position in the middle::
import pygame
pygame.init()
pygame.mixer.init()
pygame.mixer.music.load('some_file.ogg')
pygame.mixer.music.play(0,60)
This should start playing the file from the firs minute, instead on the pandora the file plays from the start.
I've tried the same code in a debian (sid) chroot (from extend utils) and it works correctly, as it does on my pc (debian wheezy).
I suspect that the issue may be present also in .next (I've done a very quick test on a friend's pandora).
Some relevant version numbers:
* libogg.so.0.6.0 (on debian libogg.so.0.8.0)
* libSDL_mixer-1.2.so.0.10.1 (on debian libSDL_mixer-1.2.so.0.12.0) |
|
297 | OpenPandora Main OS | Core | Bug Report | Low | pandora button and taskbar autohide | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
When the taskbar is set to autohide, the Pandora button does not bring up the menu anymore. |
|
299 | OpenPandora Main OS | Core | Bug Report | Low | run_pnd.sh does not follow PXML.xml or "-d"-Parameter | Assigned | |
Release 1 (Zaxxon) |
Task Description
I call pnd_run.sh with a pnd. The application directory will invariably be /media/SD/pandora/appdata/, no matter if the PXML.xml specifies a different appdata path. Also, the parameter -d for run_pnd.sh is not followed, either.
I tried with vlc.pnd from the app store and with Dosbox74.pnd.
UPDATE: Original submission contained a wrong filename reference. Corrected that typo to the filename intended by the submitter. Admin: porg. |
|
300 | OpenPandora Main OS | Core | Bug Report | Low | SuperZaxxon interprets on-disk FAT32 filenames differen... | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
With SuperZaxxon Final, I've noticed that stuff running on the Pandora like Thunar and bash are seeing a different interpretation of filenames on disk than when I remove the SD card and insert it into my desktop PC.
Specifically, the following two mismatches appear to be present when using a FAT32-formatted SD card:
First, the Pandora's VFAT support seems to be be operating with different case-handling settings than desktop Linux distros.
Filenames set in all uppercase are forced to all-lowercase on the Pandora (whether they're set on the desktop or the Pandora) but inserting the card into a PC reveals that the. All-lowercase filenames set by software on the Pandora risk appearing in all uppercase when the card is inserted into a PC. (I think the grsync PND is what created the files in question)
Among other things, this forces me to use EITHER the PND-based copy of grsync over the network OR a desktop-based copy of rsync with an SD card reader but not both because the kernel will preserve case differences like ALBION.BAT vs. albion.bat but rsync think they are separate files. (resulting in Flash-killing, time-wasting deletion and re-creation)
It also makes for irritating entries like "zzt" in DOSBox or "ddr" in PyDance where I can't capitalize the filename properly without employing Department of Redundancy Department with "DDR Songs" or "ZZT.The.Game" as an excuse for mixed case.
Second, SuperZaxxon Final seems to be using a different (though still Unicode-capable) filename encoding than all the desktop distros I've tried.
Filenames are preserved properly and all-ASCII filenames are displayed properly in all cases, but any non-ASCII characters appear as gibberish on whichever system was not used to set them.
I've confirmed this problem with these two filenames:
- 03 - The Foggy Dew with Sinéad O'Connor.flac
- Lucky Star - Native Misao (Touhou - Native Faith) ???????????????????×??????.mp4
As a Canadian user, my desktops use the "en_CA.utf8" locale and the only other distros I've found which have this problem are Slax and the 1.0 release of its successor, Porteus, both of which use ISO-8859-1 (latin1) for filenames. |
|
301 | OpenPandora Main OS | Core | Bug Report | Medium | Missing X keybinding for colon symbol | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
As verified with xev, an attached bluetooth keyboard can not generate colon (shift semicolon). xmodmap shows that (unlike a standard Linux system) shift-semicolon is mapped to NoSymbol. While it's find that there's a special symbol to get semicolon on the built-in keyboard, the other binding really should be there in support of attached keyboards. |
|
308 | OpenPandora Main OS | Core | Bug Report | Low | Wireless Network being dropped asks for password | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
When a Wireless Network that is dropped because its signal strength isn't that good gets reconnected to, I am being asked to re-input the password for that network. It would be nice if it just used the password I gave to it when it was able to connect without popping up that dialog box. |
|
315 | OpenPandora Main OS | Core | Bug Report | Medium | Pairing bluetooth SPP devices doesn't work with XFCE | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
Hi, sadly the XFCE bluetooth manager seems to have problems with pairing simple SPP devices (an BT GPS mouse here).
1. Enable BT
2. BT Manager -> Add new device
3. Confirm Dialog and wait for scanning
4. Pick device
5. Select PIN options -> "0000" (here for me)
In next step the dialog still asks you to enter a random PIN at your BT device (which is impossible here).
Thus it seems, that the XFCE dialog makes troubles, I tried it with 2 different GPS. Pairing the GPS manually works fine:
sudo rfcomm connect rfcomm0 00:18:E4:26:5F:14 |
|
320 | OpenPandora Main OS | Core | Bug Report | Low | Bluetooth connection lost after wake-up from sleep mode | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
When an internet connection was established through a mobile phone (Android, tethering) via bluetooth, the internet connection will not be re-established when the Pandora was sent to sleep and woken up again. The Pandora seems to be connected to the mobile phone, but no internet connection can be established, not even when manually trying to connect. The only way out is to disable bluetooth and enable it again.
I had similar problems with WiFi, before notaz tweaked the system (http://boards.openpandora.org/index.php/topic/11416-wifi-mysteries-resolved-once-and-for-all-—-power-saving-is-clearly-the-culprit/?p=249036). |
|
324 | OpenPandora Main OS | Core | Bug Report | Low | Sticky keys setting for shift key disabling itself afte... | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
The sticky keys option is disabling itself for the shift key. It continues to work with the left shoulder button though.
Unfortunately I have no idea what triggers the sticky option to be disabled. Sometimes it happens after 1-2 minutes, sometimes it takes longer.
I would also like to point out that using the shoulder button instead of the shift button it _not_ an option! This issue has been reported in the forums, but apperantly was never fixed. |
|
325 | OpenPandora Main OS | Core | Bug Report | Low | Impossible to not set password at first boot | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
The Wiki states that the Pandora can be used without setting a user password on first boot. But when the password and password confirmation field are left empty, an error pops up saying that there is a password missmatch.
(Please don't fix this bug by just changing the statement in the Wiki ;-) |
|
326 | OpenPandora Main OS | Core | Bug Report | Low | XFCE menu not expandingl with stylys and scrolling brok... | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
The XFCE menu does not always show submenues like "Emulators" when being clicked on with the stylus. It only works if the click lasts long or after all menues have been clicked at once with a long click.
Also, tipping on a scroll arrof of menues that are higher than the screen causes the click to be registered as a "click and hold". This leads to the menu being scrolled all the way to the end. |
|
328 | OpenPandora Main OS | Core | Bug Report | Low | XFCE desktop icons not displayed when logging on too qu... | Requires testing | |
Release 1 (Zaxxon) |
Task Description
It looks like XFCE cannot find the icons for links/launchers on the desktop, when the user logs on too quickly. This happens either when the session chooser at start-up is disabled, or when the session is being chosen quickly after the session chooser is being displayed (e.g. by pressing enter as soon as the chooser window pops up). The icons are probably not generated yet at that time point.
A simple workaround is adding the command "xfdesktop --reload" to autostart. Couls this be included in the next SuperZaxxon release or a hotfix? |
|
329 | OpenPandora Main OS | Core | Bug Report | Low | Screen turns on when LCD closed | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
Issue: The screen accidentally turns on even when the lid is closed.
How to reproduce: "Screen blanking" must be enabled! Close the lid, wait more than 10 minutes, tap either shoulder button. This behaviour happens whether on charge or battery, at the desktop or running an application, provided that the "screen blanking" option is enabled.
Desired outcome: When the Pandora comes out of "screen blanking", it should restore the brightness to the same value that it was before blanking. |
|
330 | OpenPandora Main OS | Core | Bug Report | Low | NetworkManager crashes after suspend to RAM | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
Suspend to RAM uses less power than the low power mode, but the NetworkManager crashes often after the Pandora woke up from suspend to RAM.
This could be fixed with an update of NetworkManager. |
|
331 | OpenPandora Main OS | Core | Bug Report | Medium | Hold switch key continuously sends X11 KeyPress events ... | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
When put into Hold mode, X11 handles the power switch as if it's being pressed, and it generates lots of keypress events, passing them to the foreground application. Since /dev/input/eventX does not seem to continuously trigger, I'm guessing it's due to key repeat.
To reproduce:
- Install xev and open it in the terminal
- Put the power key in HOLD mode
- Notice the "time" value changing rapidly
In addition to causing more work to X, it also floods the active application with key presses, resulting in increased CPU usage. In my test, switching to HOLD while Firefox is in the foreground causes it to use 6% CPU and X an additional 2.5%.
In addition, the key-press events continue even after the switch is taken off HOLD until another key is pressed.
A possible solution to this is to blacklist the power-button event device, to prevent evdev from listening to it (the key is handled by pndevmapperd). |
|
336 | OpenPandora Main OS | Core | Bug Report | Medium | Touch screen sensitivity too low | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
The touch screen requires to be used with the stylus or another sharp object. Even if I need to click a desktop icon, and could as well use my finger, the touch screen won't react to my finger at all (even if pressed quite hard). |
|
104 | OpenPandora Main OS | Base OS | Bug Report | Low | AAC decoder libfaad doesn't appear to be compiled as fi... | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
FAAD2 appears to not be compiled with fixed point decoding. My version of libfaad compiled with fixed point used 2-3x less cpu than the provided one. It's not enough to provide the switch to the configure script. the file libfaad/common.h has to be edited and a define uncommented. Line 68 in the v2.7 source.
/* COMPILE TIME DEFINITIONS */
/* use double precision */
/* #define USE_DOUBLE_PRECISION */
/* use fixed point reals */
//#define FIXED_POINT |
|
121 | OpenPandora Main OS | Base OS | Bug Report | Medium | PyGame Hardware support | New | |
All |
Task Description
PyGame is damn slow (games with scrolling are not at all playable).
Would be nice if Hardware surface could be used :) |
|
124 | OpenPandora Main OS | Base OS | Bug Report | Low | ifup doesn't like dhclient | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
I added:
iface usb0 inet dhcp
And ran:
ifup usb0
But dhclient simply prints usage. |
|
158 | OpenPandora Main OS | Base OS | Bug Report | Medium | Refresh rate and BPP | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
On OS Zaxon (hotfix 3).
With "xfconf-query", the resolution is 800x480@60 Hz.
But with the tool in the menu "Settings" -> "Display", the resolution is 800x480@0 Hz.
With Java (opensdk-6-jre 6b18-1.8),
GraphicsEnvironment.getLocalGraphicsEnvironment().getDefaultScreenDevice().getDisplayModes()
return 1 display mode that is 800x480@0 Hz with a BPP of -1.
It seems to be the reason that GraphicsEnvironment.getLocalGraphicsEnvironment().getDefaultScreenDevice().getDisplayMode() return null
and when closing a java application that goes in fullscreen mode to throw an exception (invalid display mode). |
|
159 | OpenPandora Main OS | Base OS | Bug Report | Medium | System > Run PND Application menu item does nothing | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
With both Hotfix 3 and Hotfix 4 Beta the Run PND Application menu item fails to do anything.
Possibly related problem is that PND files newly copied to SD card are not recognized and entered on desktop as expected.
When you go to Thunar and right click - execute the PND file, nothing happens.
Possible fix by copying the PND to another folder on the SD card with Thunar.
This makes at least two PND files I had work.
Still no response with "Run PND Application" menu, though. |
|
272 | OpenPandora Development OS | Backend / Core | Bug Report | Medium | kernel 3.2.1 DSS export omapfb update mode functions | Unconfirmed | |
AllRelease 2 (Yars Revenge) |
Task Description
The update mode functions have moved from the DSS layer to omapfb implementaion.
This patch exports the new function symbols for use by the TI drivers.
--- a/drivers/video/omap2/omapfb/omapfb-ioctl.c
+++ b/drivers/video/omap2/omapfb/omapfb-ioctl.c
@@ -22,6 +22,7 @@
#include
#include
+#include
#include
#include
#include
@@ -359,6 +360,7 @@ int omapfb_set_update_mode(struct fb_info *fbi,
return r;
}
+EXPORT_SYMBOL(omapfb_set_update_mode);
int omapfb_get_update_mode(struct fb_info *fbi,
enum omapfb_update_mode *mode)
@@ -381,6 +383,7 @@ int omapfb_get_update_mode(struct fb_info *fbi,
return 0;
}
+EXPORT_SYMBOL(omapfb_get_update_mode);
/* XXX this color key handling is a hack... */
static struct omapfb_color_key omapfb_color_keys[2]; |
|
273 | OpenPandora Development OS | Backend / Core | Bug Report | Medium | TI SGX driver package selection | Unconfirmed | |
AllRelease 2 (Yars Revenge) |
Task Description
The last release of TI Graphics SDK Product to support the 1.0.3 SGX core is 4.04.00.03
The overlay needs to peg the package selection to this version. |
|
274 | OpenPandora Development OS | Backend / Core | Bug Report | Medium | Patch for TI SGX 4.04.00.03 drivers to compile against ... | Unconfirmed | |
AllRelease 2 (Yars Revenge) |
Task Description
This patch when applied aginst TI 4.04.00.03 SGX drivers will allow building the pvr kernel modules.
This relies on task 272 (kernel patch) and should be used inconjuction with task 273
diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/3rdparty/dc_omapfb3_linux/omaplfb_displayclass.c b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/3rdparty/dc_omapfb3_linux/omaplfb_displayclass.c
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/3rdparty/dc_omapfb3_linux/omaplfb_displayclass.c 2011-06-20 21:03:33.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/3rdparty/dc_omapfb3_linux/omaplfb_displayclass.c 2012-02-09 08:37:21.000000000 +1100
@@ -830,7 +830,11 @@
unsigned long ulLCM;
unsigned uiFBDevID = psDevInfo->uiFBDevID;
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,38)
+ console_lock();
+#else
acquire_console_sem();
+#endif
psLINFBInfo = registered_fb[uiFBDevID];
if (psLINFBInfo == NULL)
@@ -972,7 +976,11 @@
ErrorModPut:
module_put(psLINFBOwner);
ErrorRelSem:
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,38)
+ console_unlock();
+#else
release_console_sem();
+#endif
return eError;
}
@@ -982,7 +990,11 @@
struct fb_info *psLINFBInfo = psDevInfo->psLINFBInfo;
struct module *psLINFBOwner;
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,38)
+ console_lock();
+#else
acquire_console_sem();
+#endif
psLINFBOwner = psLINFBInfo->fbops->owner;
@@ -993,7 +1005,11 @@
module_put(psLINFBOwner);
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,38)
+ console_unlock();
+#else
release_console_sem();
+#endif
}
static OMAPLFB_DEVINFO *OMAPLFBInitDev(unsigned uiFBDevID)
diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/3rdparty/dc_omapfb3_linux/omaplfb_linux.c b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/3rdparty/dc_omapfb3_linux/omaplfb_linux.c
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/3rdparty/dc_omapfb3_linux/omaplfb_linux.c 2011-06-20 21:03:33.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/3rdparty/dc_omapfb3_linux/omaplfb_linux.c 2012-02-09 13:14:28.000000000 +1100
@@ -24,11 +24,14 @@
*
******************************************************************************/
+
+#include
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,38)
#ifndef AUTOCONF_INCLUDED
#include
#endif
+#endif
-#include
#include
@@ -236,8 +239,11 @@
struct fb_var_screeninfo sFBVar;
int res;
unsigned long ulYResVirtual;
-
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,38)
+ console_lock();
+#else
acquire_console_sem();
+#endif
sFBVar = psDevInfo->psLINFBInfo->var;
@@ -268,31 +274,37 @@
printk(KERN_INFO DRIVER_PREFIX ": %s: Device %u: fb_pan_display failed (Y Offset: %lu, Error: %d)\n", __FUNCTION__, psDevInfo->uiFBDevID, psBuffer->ulYOffset, res);
}
}
-
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,38)
+ console_unlock();
+#else
release_console_sem();
+#endif
}
OMAPLFB_UPDATE_MODE OMAPLFBGetUpdateMode(OMAPLFB_DEVINFO *psDevInfo)
{
struct omap_dss_device *psDSSDev = fb2display(psDevInfo->psLINFBInfo);
OMAP_DSS_DRIVER(psDSSDrv, psDSSDev);
-
- enum omap_dss_update_mode eMode;
-
- if (psDSSDrv == NULL || psDSSDrv->get_update_mode == NULL)
- {
- DEBUG_PRINTK((KERN_INFO DRIVER_PREFIX ": %s: Device %u: Can't get update mode\n", __FUNCTION__, psDevInfo->uiFBDevID));
- return OMAPLFB_UPDATE_MODE_UNDEFINED;
+ if (psDSSDrv == NULL || psDSSDev == NULL)
+ {
+ DEBUG_PRINTK((KERN_INFO DRIVER_PREFIX ": %s: Device %u: No DSS device\n", __FUNCTION__, psDevInfo->uiFBDevID));
+ }
+ enum omapfb_update_mode eMode;
+
+ if (!omapfb_get_update_mode(psDevInfo->psLINFBInfo, &eMode))
+ {
+// DEBUG_PRINTK((KERN_INFO DRIVER_PREFIX ": %s: Device %u: Can't get update mode\n", __FUNCTION__, psDevInfo->uiFBDevID));
+ return OMAPLFB_UPDATE_MODE_AUTO;
+// return OMAPLFB_UPDATE_MODE_UNDEFINED;
}
- eMode = psDSSDrv->get_update_mode(psDSSDev);
switch(eMode)
{
- case OMAP_DSS_UPDATE_AUTO:
+ case OMAPFB_AUTO_UPDATE:
return OMAPLFB_UPDATE_MODE_AUTO;
- case OMAP_DSS_UPDATE_MANUAL:
+ case OMAPFB_MANUAL_UPDATE:
return OMAPLFB_UPDATE_MODE_MANUAL;
- case OMAP_DSS_UPDATE_DISABLED:
+ case OMAPFB_UPDATE_DISABLED:
return OMAPLFB_UPDATE_MODE_DISABLED;
default:
DEBUG_PRINTK((KERN_INFO DRIVER_PREFIX ": %s: Device %u: Unknown update mode (%d)\n", __FUNCTION__, psDevInfo->uiFBDevID, eMode));
@@ -307,10 +319,10 @@
{
struct omap_dss_device *psDSSDev = fb2display(psDevInfo->psLINFBInfo);
OMAP_DSS_DRIVER(psDSSDrv, psDSSDev);
- enum omap_dss_update_mode eDSSMode;
+ enum omapfb_update_mode eDSSMode;
int res;
- if (psDSSDrv == NULL || psDSSDrv->set_update_mode == NULL)
+ if (psDSSDrv == NULL)
{
DEBUG_PRINTK((KERN_INFO DRIVER_PREFIX ": %s: Device %u: Can't set update mode\n", __FUNCTION__, psDevInfo->uiFBDevID));
return OMAPLFB_FALSE;
@@ -319,20 +331,20 @@
switch(eMode)
{
case OMAPLFB_UPDATE_MODE_AUTO:
- eDSSMode = OMAP_DSS_UPDATE_AUTO;
+ eDSSMode = OMAPFB_AUTO_UPDATE;
break;
case OMAPLFB_UPDATE_MODE_MANUAL:
- eDSSMode = OMAP_DSS_UPDATE_MANUAL;
+ eDSSMode = OMAPFB_MANUAL_UPDATE;
break;
case OMAPLFB_UPDATE_MODE_DISABLED:
- eDSSMode = OMAP_DSS_UPDATE_DISABLED;
+ eDSSMode = OMAPFB_UPDATE_DISABLED;
break;
default:
DEBUG_PRINTK((KERN_INFO DRIVER_PREFIX ": %s: Device %u: Unknown update mode (%d)\n", __FUNCTION__, psDevInfo->uiFBDevID, eMode));
return OMAPLFB_FALSE;
}
- res = psDSSDrv->set_update_mode(psDSSDev, eDSSMode);
+ res = omapfb_set_update_mode(psDevInfo->psLINFBInfo, eDSSMode);
if (res != 0)
{
DEBUG_PRINTK((KERN_INFO DRIVER_PREFIX ": %s: Device %u: set_update_mode failed (%d)\n", __FUNCTION__, psDevInfo->uiFBDevID, res));
@@ -441,10 +453,17 @@
OMAPLFB_ERROR OMAPLFBUnblankDisplay(OMAPLFB_DEVINFO *psDevInfo)
{
int res;
-
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,38)
+ console_lock();
+#else
acquire_console_sem();
+#endif
res = fb_blank(psDevInfo->psLINFBInfo, 0);
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,38)
+ console_unlock();
+#else
release_console_sem();
+#endif
if (res != 0 && res != -EINVAL)
{
printk(KERN_WARNING DRIVER_PREFIX
@@ -459,9 +478,17 @@
static void OMAPLFBBlankDisplay(OMAPLFB_DEVINFO *psDevInfo)
{
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,38)
+ console_lock();
+#else
acquire_console_sem();
+#endif
fb_blank(psDevInfo->psLINFBInfo, 1);
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,38)
+ console_unlock();
+#else
release_console_sem();
+#endif
}
static void OMAPLFBEarlySuspendHandler(struct early_suspend *h)
@@ -692,9 +719,17 @@
flush_workqueue(psDevInfo->psSwapChain->psWorkQueue);
}
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,38)
+ console_lock();
+#else
acquire_console_sem();
+#endif
ret = fb_blank(psDevInfo->psLINFBInfo, iFBMode);
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,38)
+ console_unlock();
+#else
release_console_sem();
+#endif
OMAPLFBCreateSwapChainUnLock(psDevInfo);
@@ -717,7 +752,6 @@
static int __init OMAPLFB_Init(void)
#endif
{
-
if(OMAPLFBInit() != OMAPLFB_OK)
{
printk(KERN_WARNING DRIVER_PREFIX ": %s: OMAPLFBInit failed\n", __FUNCTION__);
diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/common/resman.c b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/common/resman.c
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/common/resman.c 2011-06-20 21:03:34.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/common/resman.c 2012-02-09 23:33:43.000000000 +1100
@@ -24,15 +24,17 @@
*
******************************************************************************/
+#include
#include "services_headers.h"
#include "resman.h"
#ifdef __linux__
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,38)
#ifndef AUTOCONF_INCLUDED
#include
#endif
+#endif
-#include
#include
#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,9)
#include
diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/event.c b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/event.c
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/event.c 2011-06-20 21:03:34.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/event.c 2012-02-09 09:00:12.000000000 +1100
@@ -24,11 +24,14 @@
*
******************************************************************************/
+#include
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,38)
#ifndef AUTOCONF_INCLUDED
#include
#endif
+#endif
-#include
#include
#include
#if (LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,22))
diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mmap.c b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mmap.c
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mmap.c 2011-06-20 21:03:34.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mmap.c 2012-02-09 08:56:41.000000000 +1100
@@ -24,11 +24,14 @@
*
******************************************************************************/
+#include
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,38)
#ifndef AUTOCONF_INCLUDED
#include
#endif
+#endif
-#include
#include
#include
#include
diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mm.c b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mm.c
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mm.c 2011-06-20 21:03:34.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mm.c 2012-02-09 08:52:48.000000000 +1100
@@ -24,11 +24,14 @@
*
******************************************************************************/
+#include
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,38)
#ifndef AUTOCONF_INCLUDED
#include
#endif
+#endif
-#include
#include
#include
#include
diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mm.h b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mm.h
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mm.h 2011-06-20 21:03:34.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mm.h 2012-02-09 08:55:49.000000000 +1100
@@ -27,11 +27,14 @@
#ifndef __IMG_LINUX_MM_H__
#define __IMG_LINUX_MM_H__
+#include
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,38)
#ifndef AUTOCONF_INCLUDED
#include
#endif
+#endif
-#include
#include
#include
#include
diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/module.c b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/module.c
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/module.c 2011-06-20 21:03:34.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/module.c 2012-02-09 08:59:05.000000000 +1100
@@ -24,9 +24,13 @@
*
******************************************************************************/
+#include
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,38)
#ifndef AUTOCONF_INCLUDED
#include
#endif
+#endif
#if !defined(SUPPORT_DRI_DRM)
@@ -44,7 +48,6 @@
#include
#include
#include
-#include
#include
#include
diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mutils.c b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mutils.c
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mutils.c 2011-06-20 21:03:34.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mutils.c 2012-02-10 00:24:09.000000000 +1100
@@ -24,10 +24,13 @@
*
******************************************************************************/
+#include
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,38)
#ifndef AUTOCONF_INCLUDED
#include
#endif
-#include
+#endif
#include
#include
diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mutils.h b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mutils.h
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mutils.h 2011-06-20 21:03:34.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/mutils.h 2012-02-09 08:54:31.000000000 +1100
@@ -27,11 +27,13 @@
#ifndef __IMG_LINUX_MUTILS_H__
#define __IMG_LINUX_MUTILS_H__
+#include
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,38)
#ifndef AUTOCONF_INCLUDED
#include
#endif
-
-#include
+#endif
#if !(defined(__i386__) && (LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,26)))
#if defined(SUPPORT_LINUX_X86_PAT)
diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/osfunc.c b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/osfunc.c
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/osfunc.c 2011-06-20 21:03:34.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/osfunc.c 2012-02-09 09:01:16.000000000 +1100
@@ -24,11 +24,14 @@
*
******************************************************************************/
+#include
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,38)
#ifndef AUTOCONF_INCLUDED
#include
#endif
+#endif
-#include
#include
#include
#if (LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,22))
diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/proc.c b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/proc.c
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/proc.c 2011-06-20 21:03:34.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/proc.c 2012-02-09 08:57:49.000000000 +1100
@@ -24,13 +24,16 @@
*
******************************************************************************/
+#include
+
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,38)
#ifndef AUTOCONF_INCLUDED
#include
#endif
+#endif
#include
#include
-#include
#include
#include
#include
diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/pvr_debug.c b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/pvr_debug.c
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/pvr_debug.c 2011-06-20 21:03:34.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/pvr_debug.c 2012-02-09 23:54:38.000000000 +1100
@@ -24,9 +24,12 @@
*
******************************************************************************/
+#include
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,38)
#ifndef AUTOCONF_INCLUDED
#include
#endif
+#endif
#include
#include
@@ -72,7 +75,7 @@
static PVRSRV_LINUX_MUTEX gsDebugMutexNonIRQ;
-static spinlock_t gsDebugLockIRQ = SPIN_LOCK_UNLOCKED;
+static DEFINE_SPINLOCK(gsDebugLockIRQ);
#if !defined (USE_SPIN_LOCK)
#define USE_SPIN_LOCK (in_interrupt() || !preemptible())
diff -ru a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/pvr_drm.c b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/pvr_drm.c
--- a/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/pvr_drm.c 2011-06-20 21:03:34.000000000 +1000
+++ b/Graphics_SDK_4_04_00_03/GFX_Linux_KM/services4/srvkm/env/linux/pvr_drm.c 2012-02-16 01:58:14.000000000 +1100
@@ -26,14 +26,16 @@
#if defined(SUPPORT_DRI_DRM)
+#include
+#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,38)
#ifndef AUTOCONF_INCLUDED
#include
#endif
+#endif
#include
#include
#include
-#include
#include
#include
#include
@@ -371,11 +373,23 @@
.poll = drm_poll,
.fasync = drm_fasync,
},
+#if (LINUX_VERSION_CODE name = PVR_DRM_NAME,
+// .pci->id_table = asPciIdList,
+// },
+#endif
.name = PVR_DRM_NAME,
.desc = PVR_DRM_DESC,
@@ -385,6 +399,13 @@
.patchlevel = PVRVERSION_BUILD,
};
+#if (LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,39))
+static struct pci_driver pci_pvr_driver = {
+ .name = PVR_DRM_NAME,
+ .id_table = asPciIdList,
+};
+#endif
+
static int __init PVRSRVDrmInit(void)
{
int iRes;
@@ -401,7 +422,11 @@
}
#endif
+#if (LINUX_VERSION_CODE |
|
296 | OpenPandora Development OS | Backend / Core | Bug Report | Low | upowerd fails to open file /proc/timer_stats | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
Hi,
Upowerd spams each 10 seconds with warning "failed to open file '/proc/timer_stats'".
According to https://bugzilla.redhat.com/show_bug.cgi?id=826191 this feature can be activated in kernel. I'm not sure if upowerd can be told not to check this feature, I haven't been able to find an specific option for that so far. Activating this option in kernel, this warning should be eliminated.
It would help give upowerd data it needs, and also it will stop filling up the log, which then I guess interferes with power saving (active file access while writing into log...). |
|
135 | OpenPandora Main OS | Application | Bug Report | Low | OOM Killer causes loss of items in xfce4-panel configur... | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
When the Pandora runs out of memory and the Out-Of-Memory killer fires, the Applications/Settings/xfce4/panel/panels.xml loses the entries for the menu button and the power monitor. |
|
218 | Additional Applications | Application | Bug Report | Low | nc (netcat) can't create tcp connections | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
Zaxxon Hotfix 5.
Example (dropbear is running):
------------------------
~# nc -vvvv localhost 22
Notice: Real hostname for localhost [127.0.0.1] is localhost.localdomain
Total received bytes: 0
Total sent bytes: 0
~# telnet localhost 22
SSH-2.0-dropbear_0.51
------------------------
All required libraries seem present, strace output is inconclusive. |
|
222 | OpenPandora Main OS | Application | Bug Report | Low | Login Screen does not accept all symbols of the form Fn... | Unconfirmed | |
Release 1 (Zaxxon) |
Task Description
Problem - Login Screen does not accept all symbols of the form Fn+char
Reproducibility - always
Actual results - the characters :?#|$€"‘£¥@!_ do not work on the Login Screen with the Pandora's keyboard. When fn then the corresponding character is pressed, nothing is added to the string.
Expected results - these characters should appear just like any other character
Work Around - an external keyboard was able to enter these characters
Aditional Information - While the characters :?#|$€"‘£¥@!_ do not work, the characters ;/\'-+=`() work just fine. |